- 29 Oct, 2021 1 commit
-
-
Raptor Engineering Development Team authored
This enables support for the standby-coupled VDDRA 1.2V power plane on Blackbird planar revision 1.02 and above. NOTE: When building the FPGA image for Blackbird planar revision 1.01 or below, PLATFORM_HAS_S2RAM_POWER_PLANES must be set to 0 to avoid incorrect firmware operation.
-
- 14 Jun, 2019 3 commits
-
-
Raptor Engineering Development Team authored
Bump version number
-
Raptor Engineering Development Team authored
-
Raptor Engineering Development Team authored
Set FPGA reset line to output reg instead of inout These changes fixed synthesis warnings / overrides, and are not expected to change the functionality of the resultant bitstreams.
-
- 10 May, 2019 1 commit
-
-
Raptor Engineering Development Team authored
The AST2500 GPIO pins require external pullup or pulldown resistors if they are to be used as inputs. Use pullup to retain the same conventions as Talos II.
-
- 03 May, 2019 3 commits
-
-
Raptor Engineering Development Team authored
-
Raptor Engineering Development Team authored
-
Raptor Engineering Development Team authored
This can be used to restore expected operation when NVMe drives are installed with an inverted ready line
-
- 09 Oct, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 01 Oct, 2018 1 commit
-
-
Raptor Engineering Development Team authored
Rename audio disable for clarity, and enable audio by default
-
- 30 Sep, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 14 Jun, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 11 Jun, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 06 Jun, 2018 1 commit
-
-
Raptor Engineering Development Team authored
Bump FPGA version
-
- 18 May, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 13 May, 2018 2 commits
-
-
Raptor Engineering Development Team authored
ATX PG must remain high for minimum periods according to the specification Don't try to work around faulty external power supply designs
-
Raptor Engineering Development Team authored
Expose mode select jumper to host Switch ATX PG filter to slower clock source and reduce counter width Bump FPGA version in preparation for release
-
- 03 May, 2018 1 commit
-
-
Raptor Engineering Development Team authored
The ATX specification allows up to 500ms for the ATX power good signal to be asserted after power on request Extend time from power on request to fault condition set to about 800ms in order to ensure that PSUs close to the specification margins do not induce spurious faults.
-
- 26 Apr, 2018 1 commit
-
-
Raptor Engineering Development Team authored
Reset now attempted after 30 seconds of failure to exit U-boot
-
- 23 Apr, 2018 1 commit
-
-
Raptor Engineering Development Team authored
Debounce ATX power good to work around certain Delta PSUs asserting PG before rails can be loaded Initialize various registers to 0 to save die area Bump version number for further development
-
- 15 Apr, 2018 1 commit
-
-
Raptor Engineering Development Team authored
Bump revision number reported to 0x07
-
- 12 Apr, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 08 Mar, 2018 1 commit
-
-
Raptor Engineering Development Team authored
This works around ASpeed fast blink boot hang errata (app note #3)
-
- 19 Feb, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 13 Feb, 2018 1 commit
-
-
Raptor Engineering Development Team authored
Explicitly call out register addresses
-
- 28 Jan, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 23 Jan, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 22 Jan, 2018 2 commits
-
-
Raptor Engineering Development Team authored
-
Raptor Engineering Development Team authored
-
- 19 Jan, 2018 1 commit
-
-
Raptor Engineering Development Team authored
Add front panel LED override
-
- 18 Jan, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 17 Jan, 2018 6 commits
-
-
Raptor Engineering Development Team authored
1.) Initial power-on / U-Boot: KR pattern 2.) Kernel / userspace booting: fading pattern
-
Raptor Engineering Development Team authored
Use fading startup pattern instead of prior KR pattern
-
Raptor Engineering Development Team authored
-
Raptor Engineering Development Team authored
-
Raptor Engineering Development Team authored
-
Raptor Engineering Development Team authored
-
- 16 Jan, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 14 Jan, 2018 1 commit
-
-
Raptor Engineering Development Team authored
-
- 12 Jan, 2018 1 commit
-
-
Raptor Engineering Development Team authored
Add initial internal oscillator Fix license in PCF file Tested to work on initial Talos™ II hardware
-