GitLab

The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.

So mostly this consists of better abstracting out the different sets of
regulators, clks, etc.  In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.

Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space.  And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: Rob Clark <robdclark@gmail.com>

We'll want basically the same thing for mdp5, so refactor it out so it
can be shared.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Signed-off-by: Rob Clark <robdclark@gmail.com>

This can be shared between mdp4 and mdp5.  Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: Rob Clark <robdclark@gmail.com>

resync to latest envytools db, add mdp5 registers
Signed-off-by: Rob Clark <robdclark@gmail.com>

There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: Rob Clark <robdclark@gmail.com>

This adds the necessary configuration for the APQ8060A SoC (dual-core
krait + a320 gpu) as found on the bstem board.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Add a VRAM carveout that is used for systems which do not have an IOMMU.

The VRAM carveout uses CMA.  The arch code must setup a CMA pool for the
device (preferrably in highmem.. a 256m-512m VRAM pool in lowmem is not
cool).  The user can configure the VRAM pool size using msm.vram module
param.

Technically, the abstraction of IOMMU behind msm_mmu is not strictly
needed, but it simplifies the GEM code a bit, and will be useful later
when I add support for a2xx devices with GPUMMU, so I decided to keep
this part.

It appears to be possible to configure the GPU to restrict access to
addresses within the VRAM pool, but this is not done yet.  So for now
the GPU will refuse to load if there is no sort of mmu.  Once address
based limits are supported and tested to confirm that we aren't giving
the GPU access to arbitrary memory, this restriction can be lifted
Signed-off-by: Rob Clark <robdclark@gmail.com>

This got a bit broken with original patches when re-arranging things to
move dependencies on mach-msm inside #ifndef OF.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Signed-off-by: Rob Clark <robdclark@gmail.com>

With a simple stub, we can get COMPILE_TEST support.
Signed-off-by: Rob Clark <robdclark@gmail.com>

With CONFIG_DYNAMIC_DEBUG=y, the following compile error occurs:

drivers/gpu/drm/tegra/mipi-phy.c: In function ‘mipi_dphy_timing_validate’:
drivers/gpu/drm/tegra/mipi-phy.c:69:11: error: ‘EINVAL’ undeclared (first use in this function)
drivers/gpu/drm/tegra/mipi-phy.c:69:11: note: each undeclared identifier is reported only once for each function it appears in

Fix this by directly including the header that defines EINVAL.

Fixes: dec72739

 ("drm/tegra: Add DSI support")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Implement very basic PRIME support. This currently only works with
buffers that are contiguous in memory and will refuse to import any
physically non-contiguous buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Some of the code in the CRTC's mode setting code is specific to the RGB
output or needs to be called slightly differently depending on the type
of output. Push that code down into the output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra124 and later support interlacing, but the driver doesn't support
it yet. Make sure interlacing stays disabled on hardware that supports
it.
Signed-off-by: Thierry Reding <treding@nvidia.com>

If we don't have enough memory for ->planes then we leak "fb".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

A lot of the modern userspace is capable of working without the legacy
fbdev support. kmscon can be used as a replacement for the framebuffer
console, and KMS X drivers create their own framebuffers.

Most people don't have a system where all of this works yet, though, so
leave support enabled by default.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Move the TEGRA_HOST1X and DRM_KMS_HELPER entries around to keep the list
sorted.
Signed-off-by: Thierry Reding <treding@nvidia.com>

In case of error, the devm_ioremap_resource() function returns ERR_PTR()
and never NULL. The NULL test in the return value check should therefore
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.

Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>

When an output is disabled, its DPMS mode is usually set to off. Instead
of only disabling the panel (if one is attached), turn the output off
entirely to save more power.

HDMI doesn't have any panels attached, so it previously didn't save any
power at all. With this commit, however, the complete HDMI interface
will be turned off, therefore allowing an attached monitor to go into a
standby mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The DRM core doesn't track enable and disable state of encoders and/or
connectors, so calls to the output's .enable() and .disable() are not
guaranteed to be balanced. Track the enable state internally so that
calls to regulator and clock frameworks remain balanced.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The correct check is for 48 kHz, not 480 kHz. Found by Coverity.
Signed-off-by: Thierry Reding <treding@nvidia.com>

These buffer object operations are never used outside of the GEM
implementation so there is no use in exporting them.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Signed-off-by: Thierry Reding <treding@nvidia.com>

The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: Thierry Reding <treding@nvidia.com>

All APIs that the driver uses are exported, so the driver can now be
built as a module.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra124 has 192 syncpoints whereas its predecessors had 32 syncpoints.
This required changes to the hardware register layout.
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Treat both negative and zero return values from clk_round_rate() as
errors.  This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.

Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error.  All other values will be considered valid
rates.  The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: Arto Merilainen <amerilainen@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Terje Bergström <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

When debugfs support isn't enabled, gcc complains about some variables
being unused. To avoid further #ifdefery, move debugfs specific setup
code into static functions and use IS_ENABLED(CONFIG_DEBUG_FS) to have
the compiler, rather than the preprocessor, discard them when unused.
The advantage of doing it this way is that all the code will be
compile-tested whether or not debugfs support is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Include the linux/host1x.h and dev.h headers so that function prototypes
are visible to keep sparse from suggesting that their implementations be
made static.
Signed-off-by: Thierry Reding <treding@nvidia.com>

An earlier patch added a subset of the required HW specific header files
but didn't actually include the right ones when compiling for host1x02.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Make the public API symbols visible so that depending drivers can be
built as a module.
Signed-off-by: Thierry Reding <treding@nvidia.com>

This driver adds support to perform calibration of the MIPI pads for CSI
and DSI.
Signed-off-by: Thierry Reding <treding@nvidia.com>

drivers/gpu/drm/r128/r128_state.c:1014:10-17: WARNING opportunity for memdup_user
/c/kernel-tests/src/cocci/drivers/gpu/drm/r128/r128_state.c:1029:9-16: WARNING opportunity for memdup_user
/c/kernel-tests/src/cocci/drivers/gpu/drm/r128/r128_state.c:904:10-17: WARNING opportunity for memdup_user
/c/kernel-tests/src/cocci/drivers/gpu/drm/r128/r128_state.c:914:9-16: WARNING opportunity for memdup_user

 Use memdup_user rather than duplicating its implementation
 This is a little bit restricted to reduce false positives

Generated by: coccinelle/api/memdup_user.cocci

CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This is just used for a debugfs file, and we can easily reconstruct
this number by just walking the list twice. Which isn't really bad for
a debugfs file anyway.

So let's rip this out.

There's the other issue that the dev->vmalist itself is a bit useless,
since that can be reconstructed with all the memory mapping
information from proc. But remove that is a different topic entirely.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

It's racy, and it's only used in debugfs. There are simpler ways to
know whether something is going on (like looking at dmesg with full
debugging enabled). And they're all much more useful.

So let's just rip this out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Now dev->ioctl_count tries to prevent the device from disappearing if
it's still in use. And if we'd actually need this code it would be
hopelessly racy and broken.

But luckily the vfs already takes care of this. So we can just rip it
out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This has the nice advantage that we'll get rid of a DRM_WAIT_ON user
for free.

Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>