Merge tag 'spi-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "A few core tweaks this time together with the usual collection of
  driver specific updates and fixes plus a larger than average selection
  of new device support:

   - fix DMA mapping of unaligned vmalloc() buffers

   - statistics tracking transfer volumes exposed via sysfs

   - new drivers for Freescale MPC5125, Intel Sunrise Point, Mediatek
     SoCs, and Netlogic XLP SoCs"

* tag 'spi-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (66 commits)
  spi: sh-msiof: Fix FIFO size to 64 word from 256 word
  spi: fsl-(e)spi: Fix checking return value of devm_ioremap_resource
  spi: Add DT bindings documentation for Netlogic XLP SPI controller
  spi/xlp: SPI controller driver for Netlogic XLP SoCs
  spi: fsl-espi: add runtime PM
  spi: fsl-(e)spi: simplify cleanup code
  spi: fsl-(e)spi: migrate to using devm_ functions to simplify cleanup
  spi: mediatek: fix SPI_CMD_PAUSE_IE macro error
  spi: check bits_per_word in spi_setup
  spi: mediatek: replace *_time name
  spi: mediatek: add PM clk_prepare_enable fail flow
  spi: mediatek: replace int with u32, delete TAB and define MTK_SPI_PAUSE_INT_STATUS marco
  spi: mediatek: add linux/io.h include file
  spi/bcm63xx-hsspi: add support for dual spi read/write
  spi: dw: Allow interface drivers to limit data I/O to word sizes
  dt: snps,dw-apb-ssi: Document new I/O data register width property
  spi: Fall back to master maximum speed if no slave speed specified
  spi: mediatek: use BIT() to instead of SPI_CMD_*_OFFSET
  spi: medaitek: revise quirks compatibility style
  spi: mediatek: fix spi incorrect endian usage
  ...

Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt

@@ -6,14 +6,14 @@ PSC in UART mode
 For PSC in UART mode the needed PSC serial devices
 are specified by fsl,mpc5121-psc-uart nodes in the
 fsl,mpc5121-immr SoC node. Additionally the PSC FIFO
-Controller node fsl,mpc5121-psc-fifo is requered there:
+Controller node fsl,mpc5121-psc-fifo is required there:
 
-fsl,mpc5121-psc-uart nodes
+fsl,mpc512x-psc-uart nodes
 --------------------------
 
 Required properties :
- - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc"
- - cell-index : Index of the PSC in hardware
+ - compatible : Should contain "fsl,<soc>-psc-uart" and "fsl,<soc>-psc"
+   Supported <soc>s: mpc5121, mpc5125
  - reg : Offset and length of the register set for the PSC device
  - interrupts : <a b> where a is the interrupt number of the
    PSC FIFO Controller and b is a field that represents an
@@ -25,12 +25,21 @@ Recommended properties :
  - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4)
  - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4)
 
+PSC in SPI mode
+---------------
 
-fsl,mpc5121-psc-fifo node
+Similar to the UART mode a PSC can be operated in SPI mode. The compatible used
+for that is fsl,mpc5121-psc-spi. It requires a fsl,mpc5121-psc-fifo as well.
+The required and recommended properties are identical to the
+fsl,mpc5121-psc-uart nodes, just use spi instead of uart in the compatible
+string.
+
+fsl,mpc512x-psc-fifo node
 -------------------------
 
 Required properties :
- - compatible : Should be "fsl,mpc5121-psc-fifo"
+ - compatible : Should be "fsl,<soc>-psc-fifo"
+   Supported <soc>s: mpc5121, mpc5125
  - reg : Offset and length of the register set for the PSC
          FIFO Controller
  - interrupts : <a b> where a is the interrupt number of the
@@ -39,6 +48,9 @@ Required properties :
  - interrupt-parent : the phandle for the interrupt controller that
    services interrupts for this device.
 
+Recommended properties :
+ - clocks : specifies the clock needed to operate the fifo controller
+ - clock-names : name(s) for the clock(s) listed in clocks
 
 Example for a board using PSC0 and PSC1 devices in serial mode:
 

Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt

@@ -10,6 +10,8 @@ Required properties:
 Optional properties:
 - cs-gpios : Specifies the gpio pis to be used for chipselects.
 - num-cs : The number of chipselects. If omitted, this will default to 4.
+- reg-io-width : The I/O register width (in bytes) implemented by this
+  device.  Supported values are 2 or 4 (the default).
 
 Child nodes as per the generic SPI binding.
 

Documentation/devicetree/bindings/spi/spi-davinci.txt

@@ -12,6 +12,8 @@ Required properties:
 - compatible:
 	- "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family
 	- "ti,da830-spi" for SPI used similar to that on DA8xx SoC family
+	- "ti,keystone-spi" for SPI used similar to that on Keystone2 SoC
+		family
 - reg: Offset and length of SPI controller register space
 - num-cs: Number of chip selects. This includes internal as well as
 	GPIO chip selects.

Documentation/devicetree/bindings/spi/spi-img-spfi.txt

@@ -21,6 +21,7 @@ Required properties:
 Optional properties:
 - img,supports-quad-mode: Should be set if the interface supports quad mode
   SPI transfers.
+- spfi-max-frequency: Maximum speed supported by the spfi block.
 
 Example:
 

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

+Binding for MTK SPI controller
+
+Required properties:
+- compatible: should be one of the following.
+    - mediatek,mt8173-spi: for mt8173 platforms
+    - mediatek,mt8135-spi: for mt8135 platforms
+    - mediatek,mt6589-spi: for mt6589 platforms
+
+- #address-cells: should be 1.
+
+- #size-cells: should be 0.
+
+- reg: Address and length of the register set for the device
+
+- interrupts: Should contain spi interrupt
+
+- clocks: phandles to input clocks.
+  The first should be <&topckgen CLK_TOP_SPI_SEL>.
+  The second should be one of the following.
+   -  <&clk26m>: specify parent clock 26MHZ.
+   -  <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ.
+				      It's the default one.
+   -  <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ.
+   -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
+   -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+
+- clock-names: shall be "spi-clk" for the controller clock, and
+  "parent-clk" for the parent clock.
+
+Optional properties:
+- mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
+  controller used, this value should be 0~3, only required for MT8173.
+    0: specify GPIO69,70,71,72 for spi pins.
+    1: specify GPIO102,103,104,105 for spi pins.
+    2: specify GPIO128,129,130,131 for spi pins.
+    3: specify GPIO5,6,7,8 for spi pins.
+
+Example:
+
+- SoC Specific Portion:
+spi: spi@1100a000 {
+	compatible = "mediatek,mt8173-spi";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0 0x1100a000 0 0x1000>;
+	interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>;
+	clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>;
+	clock-names = "spi-clk", "parent-clk";
+	mediatek,pad-select = <0>;
+	status = "disabled";
+};

Documentation/devicetree/bindings/spi/spi-xlp.txt

+SPI Master controller for Netlogic XLP MIPS64 SOCs
+==================================================
+
+Currently this SPI controller driver is supported for the following
+Netlogic XLP SoCs:
+	XLP832, XLP316, XLP208, XLP980, XLP532
+
+Required properties:
+- compatible		: Should be "netlogic,xlp832-spi".
+- #address-cells	: Number of cells required to define a chip select address
+			  on the SPI bus.
+- #size-cells		: Should be zero.
+- reg			: Should contain register location and length.
+- clocks		: Phandle of the spi clock
+- interrupts		: Interrupt number used by this controller.
+- interrupt-parent	: Phandle of the parent interrupt controller.
+
+SPI slave nodes must be children of the SPI master node and can contain
+properties described in Documentation/devicetree/bindings/spi/spi-bus.txt.
+
+Example:
+
+	spi: xlp_spi@3a100 {
+		compatible = "netlogic,xlp832-spi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0 0x3a100 0x100>;
+		clocks = <&spi_clk>;
+		interrupts = <34>;
+		interrupt-parent = <&pic>;
+
+		spi_nor@1 {
+			compatible = "spansion,s25sl12801";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <1>;	/* Chip Select */
+			spi-max-frequency = <40000000>;
+		};
+};

arch/arm/mach-davinci/devices-da8xx.c

@@ -1010,11 +1010,13 @@ static struct davinci_spi_platform_data da8xx_spi_pdata[] = {
 		.version	= SPI_VERSION_2,
 		.intr_line	= 1,
 		.dma_event_q	= EVENTQ_0,
+		.prescaler_limit = 2,
 	},
 	[1] = {
 		.version	= SPI_VERSION_2,
 		.intr_line	= 1,
 		.dma_event_q	= EVENTQ_0,
+		.prescaler_limit = 2,
 	},
 };
 

arch/arm/mach-davinci/dm355.c

@@ -411,6 +411,7 @@ static struct davinci_spi_platform_data dm355_spi0_pdata = {
 	.num_chipselect = 2,
 	.cshold_bug	= true,
 	.dma_event_q	= EVENTQ_1,
+	.prescaler_limit = 1,
 };
 static struct platform_device dm355_spi0_device = {
 	.name = "spi_davinci",

arch/arm/mach-davinci/dm365.c

@@ -646,6 +646,7 @@ static struct davinci_spi_platform_data dm365_spi0_pdata = {
 	.version 	= SPI_VERSION_1,
 	.num_chipselect = 2,
 	.dma_event_q	= EVENTQ_3,
+	.prescaler_limit = 1,
 };
 
 static struct resource dm365_spi0_resources[] = {

arch/powerpc/include/asm/mpc52xx_psc.h

@@ -150,7 +150,10 @@
 
 /* Structure of the hardware registers */
 struct mpc52xx_psc {
-	u8		mode;		/* PSC + 0x00 */
+	union {
+		u8	mode;		/* PSC + 0x00 */
+		u8	mr2;
+	};
 	u8		reserved0[3];
 	union {				/* PSC + 0x04 */
 		u16	status;

drivers/spi/Kconfig

@@ -326,6 +326,15 @@ config SPI_MESON_SPIFC
 	  This enables master mode support for the SPIFC (SPI flash
 	  controller) available in Amlogic Meson SoCs.
 
+config SPI_MT65XX
+	tristate "MediaTek SPI controller"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	help
+	  This selects the MediaTek(R) SPI bus driver.
+	  If you want to use MediaTek(R) SPI interface,
+	  say Y or M here.If you are not sure, say N.
+	  SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
+
 config SPI_OC_TINY
 	tristate "OpenCores tiny SPI"
 	depends on GPIOLIB || COMPILE_TEST
@@ -598,6 +607,17 @@ config SPI_XILINX
 
 	  Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 
+config SPI_XLP
+	tristate "Netlogic XLP SPI controller driver"
+	depends on CPU_XLP || COMPILE_TEST
+	help
+	  Enable support for the SPI controller on the Netlogic XLP SoCs.
+	  Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
+	  and XLP5XX.
+
+	  If you have a Netlogic XLP platform say Y here.
+	  If unsure, say N.
+
 config SPI_XTENSA_XTFPGA
 	tristate "Xtensa SPI controller for xtfpga"
 	depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST

drivers/spi/Makefile

@@ -48,6 +48,7 @@ obj-$(CONFIG_SPI_MESON_SPIFC)		+= spi-meson-spifc.o
 obj-$(CONFIG_SPI_MPC512x_PSC)		+= spi-mpc512x-psc.o
 obj-$(CONFIG_SPI_MPC52xx_PSC)		+= spi-mpc52xx-psc.o
 obj-$(CONFIG_SPI_MPC52xx)		+= spi-mpc52xx.o
+obj-$(CONFIG_SPI_MT65XX)                += spi-mt65xx.o
 obj-$(CONFIG_SPI_MXS)			+= spi-mxs.o
 obj-$(CONFIG_SPI_NUC900)		+= spi-nuc900.o
 obj-$(CONFIG_SPI_OC_TINY)		+= spi-oc-tiny.o
@@ -88,5 +89,6 @@ obj-$(CONFIG_SPI_TOPCLIFF_PCH)		+= spi-topcliff-pch.o
 obj-$(CONFIG_SPI_TXX9)			+= spi-txx9.o
 obj-$(CONFIG_SPI_XCOMM)		+= spi-xcomm.o
 obj-$(CONFIG_SPI_XILINX)		+= spi-xilinx.o
+obj-$(CONFIG_SPI_XLP)			+= spi-xlp.o
 obj-$(CONFIG_SPI_XTENSA_XTFPGA)		+= spi-xtensa-xtfpga.o
 obj-$(CONFIG_SPI_ZYNQMP_GQSPI)		+= spi-zynqmp-gqspi.o

drivers/spi/spi-atmel.c

@@ -19,7 +19,6 @@
 #include <linux/interrupt.h>
 #include <linux/spi/spi.h>
 #include <linux/slab.h>
-#include <linux/platform_data/atmel.h>
 #include <linux/platform_data/dma-atmel.h>
 #include <linux/of.h>
 

drivers/spi/spi-bcm2835.c

@@ -480,7 +480,7 @@ static int bcm2835_spi_transfer_one_poll(struct spi_master *master,
 					 struct spi_device *spi,
 					 struct spi_transfer *tfr,
 					 u32 cs,
-					 unsigned long xfer_time_us)
+					 unsigned long long xfer_time_us)
 {
 	struct bcm2835_spi *bs = spi_master_get_devdata(master);
 	unsigned long timeout;
@@ -531,7 +531,8 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
 {
 	struct bcm2835_spi *bs = spi_master_get_devdata(master);
 	unsigned long spi_hz, clk_hz, cdiv;
-	unsigned long spi_used_hz, xfer_time_us;
+	unsigned long spi_used_hz;
+	unsigned long long xfer_time_us;
 	u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
 
 	/* set clock */
@@ -553,13 +554,11 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
 	spi_used_hz = cdiv ? (clk_hz / cdiv) : (clk_hz / 65536);
 	bcm2835_wr(bs, BCM2835_SPI_CLK, cdiv);
 
-	/* handle all the modes */
+	/* handle all the 3-wire mode */
 	if ((spi->mode & SPI_3WIRE) && (tfr->rx_buf))
 		cs |= BCM2835_SPI_CS_REN;
-	if (spi->mode & SPI_CPOL)
-		cs |= BCM2835_SPI_CS_CPOL;
-	if (spi->mode & SPI_CPHA)
-		cs |= BCM2835_SPI_CS_CPHA;
+	else
+		cs &= ~BCM2835_SPI_CS_REN;
 
 	/* for gpio_cs set dummy CS so that no HW-CS get changed
 	 * we can not run this in bcm2835_spi_set_cs, as it does
@@ -575,9 +574,10 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
 	bs->rx_len = tfr->len;
 
 	/* calculate the estimated time in us the transfer runs */
-	xfer_time_us = tfr->len
+	xfer_time_us = (unsigned long long)tfr->len
 		* 9 /* clocks/byte - SPI-HW waits 1 clock after each byte */
-		* 1000000 / spi_used_hz;
+		* 1000000;
+	do_div(xfer_time_us, spi_used_hz);
 
 	/* for short requests run polling*/
 	if (xfer_time_us <= BCM2835_SPI_POLLING_LIMIT_US)
@@ -592,6 +592,25 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
 	return bcm2835_spi_transfer_one_irq(master, spi, tfr, cs);
 }
 
+static int bcm2835_spi_prepare_message(struct spi_master *master,
+				       struct spi_message *msg)
+{
+	struct spi_device *spi = msg->spi;
+	struct bcm2835_spi *bs = spi_master_get_devdata(master);
+	u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+
+	cs &= ~(BCM2835_SPI_CS_CPOL | BCM2835_SPI_CS_CPHA);
+
+	if (spi->mode & SPI_CPOL)
+		cs |= BCM2835_SPI_CS_CPOL;
+	if (spi->mode & SPI_CPHA)
+		cs |= BCM2835_SPI_CS_CPHA;
+
+	bcm2835_wr(bs, BCM2835_SPI_CS, cs);
+
+	return 0;
+}
+
 static void bcm2835_spi_handle_err(struct spi_master *master,
 				   struct spi_message *msg)
 {
@@ -739,6 +758,7 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 	master->set_cs = bcm2835_spi_set_cs;
 	master->transfer_one = bcm2835_spi_transfer_one;
 	master->handle_err = bcm2835_spi_handle_err;
+	master->prepare_message = bcm2835_spi_prepare_message;
 	master->dev.of_node = pdev->dev.of_node;
 
 	bs = spi_master_get_devdata(master);

drivers/spi/spi-bcm63xx-hsspi.c

@@ -76,6 +76,7 @@
 #define HSSPI_FIFO_REG(x)			(0x200 + (x) * 0x200)
 
 
+#define HSSPI_OP_MULTIBIT			BIT(11)
 #define HSSPI_OP_CODE_SHIFT			13
 #define HSSPI_OP_SLEEP				(0 << HSSPI_OP_CODE_SHIFT)
 #define HSSPI_OP_READ_WRITE			(1 << HSSPI_OP_CODE_SHIFT)
@@ -171,9 +172,12 @@ static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t)
 	if (opcode != HSSPI_OP_READ)
 		step_size -= HSSPI_OPCODE_LEN;
 
-	__raw_writel(0 << MODE_CTRL_PREPENDBYTE_CNT_SHIFT |
-		     2 << MODE_CTRL_MULTIDATA_WR_STRT_SHIFT |
-		     2 << MODE_CTRL_MULTIDATA_RD_STRT_SHIFT | 0xff,
+	if ((opcode == HSSPI_OP_READ && t->rx_nbits == SPI_NBITS_DUAL) ||
+	    (opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL))
+		opcode |= HSSPI_OP_MULTIBIT;
+
+	__raw_writel(1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT |
+		     1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT | 0xff,
 		     bs->regs + HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
 
 	while (pending > 0) {
@@ -374,7 +378,8 @@ static int bcm63xx_hsspi_probe(struct platform_device *pdev)
 	master->num_chipselect = 8;
 	master->setup = bcm63xx_hsspi_setup;
 	master->transfer_one_message = bcm63xx_hsspi_transfer_one;
-	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH |
+			    SPI_RX_DUAL | SPI_TX_DUAL;
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
 	master->auto_runtime_pm = true;
 

drivers/spi/spi-bitbang-txrx.h

@@ -49,7 +49,7 @@ bitbang_txrx_be_cpha0(struct spi_device *spi,
 {
 	/* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */
 
-	bool oldbit = !(word & 1);
+	u32 oldbit = (!(word & (1<<(bits-1)))) << 31;
 	/* clock starts at inactive polarity */
 	for (word <<= (32 - bits); likely(bits); bits--) {
 
@@ -81,7 +81,7 @@ bitbang_txrx_be_cpha1(struct spi_device *spi,
 {
 	/* if (cpol == 0) this is SPI_MODE_1; else this is SPI_MODE_3 */
 
-	bool oldbit = !(word & (1 << 31));
+	u32 oldbit = (!(word & (1<<(bits-1)))) << 31;
 	/* clock starts at inactive polarity */
 	for (word <<= (32 - bits); likely(bits); bits--) {
 

drivers/spi/spi-davinci.c

@@ -139,6 +139,8 @@ struct davinci_spi {
 	u32			(*get_tx)(struct davinci_spi *);
 
 	u8			*bytes_per_word;
+
+	u8			prescaler_limit;
 };
 
 static struct davinci_spi_config davinci_spi_default_cfg;
@@ -255,7 +257,7 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value)
  * This function calculates the prescale value that generates a clock rate
  * less than or equal to the specified maximum.
  *
- * Returns: calculated prescale - 1 for easy programming into SPI registers
+ * Returns: calculated prescale value for easy programming into SPI registers
  * or negative error number if valid prescalar cannot be updated.
  */
 static inline int davinci_spi_get_prescale(struct davinci_spi *dspi,
@@ -263,12 +265,13 @@ static inline int davinci_spi_get_prescale(struct davinci_spi *dspi,
 {
 	int ret;
 
-	ret = DIV_ROUND_UP(clk_get_rate(dspi->clk), max_speed_hz);
+	/* Subtract 1 to match what will be programmed into SPI register. */
+	ret = DIV_ROUND_UP(clk_get_rate(dspi->clk), max_speed_hz) - 1;
 
-	if (ret < 1 || ret > 256)
+	if (ret < dspi->prescaler_limit || ret > 255)
 		return -EINVAL;
 
-	return ret - 1;
+	return ret;
 }
 
 /**
@@ -832,13 +835,40 @@ static int davinci_spi_request_dma(struct davinci_spi *dspi)
 }
 
 #if defined(CONFIG_OF)
+
+/* OF SPI data structure */
+struct davinci_spi_of_data {
+	u8	version;
+	u8	prescaler_limit;
+};
+
+static const struct davinci_spi_of_data dm6441_spi_data = {
+	.version = SPI_VERSION_1,
+	.prescaler_limit = 2,
+};
+
+static const struct davinci_spi_of_data da830_spi_data = {
+	.version = SPI_VERSION_2,
+	.prescaler_limit = 2,
+};
+
+static const struct davinci_spi_of_data keystone_spi_data = {
+	.version = SPI_VERSION_1,
+	.prescaler_limit = 0,
+};
+
 static const struct of_device_id davinci_spi_of_match[] = {
 	{
 		.compatible = "ti,dm6441-spi",
+		.data = &dm6441_spi_data,
 	},
 	{
 		.compatible = "ti,da830-spi",
-		.data = (void *)SPI_VERSION_2,
+		.data = &da830_spi_data,
+	},
+	{
+		.compatible = "ti,keystone-spi",
+		.data = &keystone_spi_data,
 	},
 	{ },
 };
@@ -857,21 +887,21 @@ static int spi_davinci_get_pdata(struct platform_device *pdev,
 			struct davinci_spi *dspi)
 {
 	struct device_node *node = pdev->dev.of_node;
+	struct davinci_spi_of_data *spi_data;
 	struct davinci_spi_platform_data *pdata;
 	unsigned int num_cs, intr_line = 0;
 	const struct of_device_id *match;
 
 	pdata = &dspi->pdata;
 
-	pdata->version = SPI_VERSION_1;
 	match = of_match_device(davinci_spi_of_match, &pdev->dev);
 	if (!match)
 		return -ENODEV;
 
-	/* match data has the SPI version number for SPI_VERSION_2 */
-	if (match->data == (void *)SPI_VERSION_2)
-		pdata->version = SPI_VERSION_2;
+	spi_data = (struct davinci_spi_of_data *)match->data;
 
+	pdata->version = spi_data->version;
+	pdata->prescaler_limit = spi_data->prescaler_limit;
 	/*
 	 * default num_cs is 1 and all chipsel are internal to the chip
 	 * indicated by chip_sel being NULL or cs_gpios being NULL or
@@ -991,7 +1021,7 @@ static int davinci_spi_probe(struct platform_device *pdev)
 
 	dspi->bitbang.chipselect = davinci_spi_chipselect;
 	dspi->bitbang.setup_transfer = davinci_spi_setup_transfer;
-
+	dspi->prescaler_limit = pdata->prescaler_limit;
 	dspi->version = pdata->version;
 
 	dspi->bitbang.flags = SPI_NO_CS | SPI_LSB_FIRST | SPI_LOOP;

drivers/spi/spi-dw-mmio.c

@@ -74,6 +74,9 @@ static int dw_spi_mmio_probe(struct platform_device *pdev)
 
 	dws->max_freq = clk_get_rate(dwsmmio->clk);
 
+	of_property_read_u32(pdev->dev.of_node, "reg-io-width",
+			     &dws->reg_io_width);
+
 	num_cs = 4;
 
 	if (pdev->dev.of_node)

drivers/spi/spi-dw.c

@@ -194,7 +194,7 @@ static void dw_writer(struct dw_spi *dws)
 			else
 				txw = *(u16 *)(dws->tx);
 		}
-		dw_writel(dws, DW_SPI_DR, txw);
+		dw_write_io_reg(dws, DW_SPI_DR, txw);
 		dws->tx += dws->n_bytes;
 	}
 }
@@ -205,7 +205,7 @@ static void dw_reader(struct dw_spi *dws)
 	u16 rxw;
 
 	while (max--) {
-		rxw = dw_readl(dws, DW_SPI_DR);
+		rxw = dw_read_io_reg(dws, DW_SPI_DR);
 		/* Care rx only if the transfer's original "rx" is not null */
 		if (dws->rx_end - dws->len) {
 			if (dws->n_bytes == 1)

drivers/spi/spi-dw.h

@@ -109,6 +109,7 @@ struct dw_spi {
 	u32			fifo_len;	/* depth of the FIFO buffer */
 	u32			max_freq;	/* max bus freq supported */
 
+	u32			reg_io_width;	/* DR I/O width in bytes */
 	u16			bus_num;
 	u16			num_cs;		/* supported slave numbers */
 
@@ -145,11 +146,45 @@ static inline u32 dw_readl(struct dw_spi *dws, u32 offset)
 	return __raw_readl(dws->regs + offset);
 }
 
+static inline u16 dw_readw(struct dw_spi *dws, u32 offset)
+{
+	return __raw_readw(dws->regs + offset);
+}
+
 static inline void dw_writel(struct dw_spi *dws, u32 offset, u32 val)
 {
 	__raw_writel(val, dws->regs + offset);
 }
 
+static inline void dw_writew(struct dw_spi *dws, u32 offset, u16 val)
+{
+	__raw_writew(val, dws->regs + offset);
+}
+
+static inline u32 dw_read_io_reg(struct dw_spi *dws, u32 offset)
+{
+	switch (dws->reg_io_width) {
+	case 2:
+		return dw_readw(dws, offset);
+	case 4:
+	default:
+		return dw_readl(dws, offset);
+	}
+}
+
+static inline void dw_write_io_reg(struct dw_spi *dws, u32 offset, u32 val)
+{
+	switch (dws->reg_io_width) {
+	case 2:
+		dw_writew(dws, offset, val);
+		break;
+	case 4:
+	default:
+		dw_writel(dws, offset, val);
+		break;
+	}
+}
+
 static inline void spi_enable_chip(struct dw_spi *dws, int enable)
 {
 	dw_writel(dws, DW_SPI_SSIENR, (enable ? 1 : 0));