Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Another batch of fixes for ARM SoCs for 3.13.  The diffstat is large,
  mostly because of:

   - Another set of fixes to fix regressions caused by moving OMAP from
     board files to DT.  Tony thinks this was the last major set of
     fixes, with maybe just a few small patches to follow.
   - More fixes for Marvell platforms, most dealing with misdescribed
     PCIe hardware, i.e.  incorrect number of busses on some SoCs, etc.
     The line delta adds up due to various ranges moving around when
     this is fixed.

  But there's also:

   - Some smaller tweaks to defconfigs to make more boards bootable in
     my test setup for better coverage.
   - There are also a few other smaller fixes, a short series for at91,
     a couple of reverts for ux500, etc"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
  arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
  arm: socfpga: Enable ARM_TWD for socfpga
  ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
  ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
  ARM: multi_v7_defconfig: enable network for BeagleBone Black
  ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
  ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
  ARM: dts: omap3-beagle: Add omap-twl4030 audio support
  ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
  ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
  ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
  ARM: at91: add usart3 alias to dtsi
  ARM: at91: sama5d3: reduce TWI internal clock frequency
  mmc: omap: Fix I2C dependency and make driver usable with device tree
  mmc: omap: Fix DMA configuration to not rely on device id
  ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
  ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
  ARM: dts: AM33XX IGEP0033: add USB support
  ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
  ARM: dts: AM33XX BASE0033: add pinmux and user led support
  ...

Documentation/devicetree/bindings/mmc/ti-omap.txt

+* TI MMC host controller for OMAP1 and 2420
+
+The MMC Host Controller on TI OMAP1 and 2420 family provides
+an interface for MMC, SD, and SDIO types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the omap mmc driver.
+
+Note that this driver will not work with omap2430 or later omaps,
+please see the omap hsmmc driver for the current omaps.
+
+Required properties:
+- compatible: Must be "ti,omap2420-mmc", for OMAP2420 controllers
+- ti,hwmods: For 2420, must be "msdi<n>", where n is controller
+  instance starting 1
+
+Examples:
+
+	msdi1: mmc@4809c000 {
+		compatible = "ti,omap2420-mmc";
+		ti,hwmods = "msdi1";
+		reg = <0x4809c000 0x80>;
+		interrupts = <83>;
+		dmas = <&sdma 61 &sdma 62>;
+		dma-names = "tx", "rx";
+	};
+
+* TI MMC host controller for OMAP1 and 2420
+
+The MMC Host Controller on TI OMAP1 and 2420 family provides
+an interface for MMC, SD, and SDIO types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the omap mmc driver.
+
+Note that this driver will not work with omap2430 or later omaps,
+please see the omap hsmmc driver for the current omaps.
+
+Required properties:
+- compatible: Must be "ti,omap2420-mmc", for OMAP2420 controllers
+- ti,hwmods: For 2420, must be "msdi<n>", where n is controller
+  instance starting 1
+
+Examples:
+
+	msdi1: mmc@4809c000 {
+		compatible = "ti,omap2420-mmc";
+		ti,hwmods = "msdi1";
+		reg = <0x4809c000 0x80>;
+		interrupts = <83>;
+		dmas = <&sdma 61 &sdma 62>;
+		dma-names = "tx", "rx";
+	};
+

arch/arm/boot/dts/am335x-base0033.dts

@@ -13,4 +13,83 @@
 / {
 	model = "IGEP COM AM335x on AQUILA Expansion";
 	compatible = "isee,am335x-base0033", "isee,am335x-igep0033", "ti,am33xx";
+
+	hdmi {
+		compatible = "ti,tilcdc,slave";
+		i2c = <&i2c0>;
+		pinctrl-names = "default", "off";
+		pinctrl-0 = <&nxp_hdmi_pins>;
+		pinctrl-1 = <&nxp_hdmi_off_pins>;
+		status = "okay";
+	};
+
+	leds_base {
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_base_pins>;
+
+		compatible = "gpio-leds";
+
+		led@0 {
+			label = "base:red:user";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;	/* gpio1_21 */
+			default-state = "off";
+		};
+
+		led@1 {
+			label = "base:green:user";
+			gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;	/* gpio2_0 */
+			default-state = "off";
+		};
+	};
+};
+
+&am33xx_pinmux {
+	nxp_hdmi_pins: pinmux_nxp_hdmi_pins {
+		pinctrl-single,pins = <
+			0x1b0 (PIN_OUTPUT | MUX_MODE3)	/* xdma_event_intr0.clkout1 */
+			0xa0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data0 */
+			0xa4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data1 */
+			0xa8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data2 */
+			0xac (PIN_OUTPUT | MUX_MODE0)	/* lcd_data3 */
+			0xb0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data4 */
+			0xb4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data5 */
+			0xb8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data6 */
+			0xbc (PIN_OUTPUT | MUX_MODE0)	/* lcd_data7 */
+			0xc0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data8 */
+			0xc4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data9 */
+			0xc8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data10 */
+			0xcc (PIN_OUTPUT | MUX_MODE0)	/* lcd_data11 */
+			0xd0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data12 */
+			0xd4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data13 */
+			0xd8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data14 */
+			0xdc (PIN_OUTPUT | MUX_MODE0)	/* lcd_data15 */
+			0xe0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_vsync */
+			0xe4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_hsync */
+			0xe8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_pclk */
+			0xec (PIN_OUTPUT | MUX_MODE0)	/* lcd_ac_bias_en */
+		>;
+	};
+	nxp_hdmi_off_pins: pinmux_nxp_hdmi_off_pins {
+		pinctrl-single,pins = <
+			0x1b0 (PIN_OUTPUT | MUX_MODE3)	/* xdma_event_intr0.clkout1 */
+		>;
+	};
+
+	leds_base_pins: pinmux_leds_base_pins {
+		pinctrl-single,pins = <
+			0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
+			0x88 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn3.gpio2_0 */
+		>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+};
+
+&i2c0 {
+	eeprom: eeprom@50 {
+		compatible = "at,24c256";
+		reg = <0x50>;
+	};
 };

arch/arm/boot/dts/am335x-igep0033.dtsi

@@ -199,6 +199,35 @@
 	pinctrl-0 = <&uart0_pins>;
 };
 
+&usb {
+	status = "okay";
+
+	control@44e10000 {
+		status = "okay";
+	};
+
+	usb-phy@47401300 {
+		status = "okay";
+	};
+
+	usb-phy@47401b00 {
+		status = "okay";
+	};
+
+	usb@47401000 {
+		status = "okay";
+	};
+
+	usb@47401800 {
+		status = "okay";
+		dr_mode = "host";
+	};
+
+	dma-controller@07402000  {
+		status = "okay";
+	};
+};
+
 #include "tps65910.dtsi"
 
 &tps {

arch/arm/boot/dts/armada-370-db.dts

@@ -99,22 +99,22 @@
 					spi-max-frequency = <50000000>;
 				};
 			};
+		};
 
-			pcie-controller {
+		pcie-controller {
+			status = "okay";
+			/*
+			 * The two PCIe units are accessible through
+			 * both standard PCIe slots and mini-PCIe
+			 * slots on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
 				status = "okay";
-				/*
-				 * The two PCIe units are accessible through
-				 * both standard PCIe slots and mini-PCIe
-				 * slots on the board.
-				 */
-				pcie@1,0 {
-					/* Port 0, Lane 0 */
-					status = "okay";
-				};
-				pcie@2,0 {
-					/* Port 1, Lane 0 */
-					status = "okay";
-				};
 			};
 		};
 	};

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -118,7 +118,7 @@
 
 			coherency-fabric@20200 {
 				compatible = "marvell,coherency-fabric";
-				reg = <0x20200 0xb0>, <0x21810 0x1c>;
+				reg = <0x20200 0xb0>, <0x21010 0x1c>;
 			};
 
 			serial@12000 {

arch/arm/boot/dts/armada-xp-mv78230.dtsi

@@ -47,7 +47,7 @@
 		/*
 		 * MV78230 has 2 PCIe units Gen2.0: One unit can be
 		 * configured as x4 or quad x1 lanes. One unit is
-		 * x4/x1.
+		 * x1 only.
 		 */
 		pcie-controller {
 			compatible = "marvell,armada-xp-pcie";
@@ -62,10 +62,10 @@
 
 			ranges =
 			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000   /* Port 0.0 registers */
-				0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000   /* Port 2.0 registers */
 				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000   /* Port 0.1 registers */
 				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000   /* Port 0.2 registers */
 				0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000   /* Port 0.3 registers */
+				0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000   /* Port 1.0 registers */
 				0x82000000 0x1 0       MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
 				0x81000000 0x1 0       MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
 				0x82000000 0x2 0       MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
@@ -74,8 +74,8 @@
 				0x81000000 0x3 0       MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO  */
 				0x82000000 0x4 0       MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
 				0x81000000 0x4 0       MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO  */
-				0x82000000 0x9 0       MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
-				0x81000000 0x9 0       MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO  */>;
+				0x82000000 0x5 0       MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+				0x81000000 0x5 0       MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */>;
 
 			pcie@1,0 {
 				device_type = "pci";
@@ -145,20 +145,20 @@
 				status = "disabled";
 			};
 
-			pcie@9,0 {
+			pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
-				reg = <0x4800 0 0 0 0>;
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
 				#interrupt-cells = <1>;
-				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
-					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
+				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
-				marvell,pcie-port = <2>;
+				interrupt-map = <0 0 0 0 &mpic 62>;
+				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 26>;
+				clocks = <&gateclk 9>;
 				status = "disabled";
 			};
 		};

arch/arm/boot/dts/armada-xp-mv78260.dtsi

@@ -48,7 +48,7 @@
 		/*
 		 * MV78260 has 3 PCIe units Gen2.0: Two units can be
 		 * configured as x4 or quad x1 lanes. One unit is
-		 * x4/x1.
+		 * x4 only.
 		 */
 		pcie-controller {
 			compatible = "marvell,armada-xp-pcie";
@@ -68,7 +68,9 @@
 				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000   /* Port 0.2 registers */
 				0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000   /* Port 0.3 registers */
 				0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000   /* Port 1.0 registers */
-				0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000   /* Port 3.0 registers */
+				0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000   /* Port 1.1 registers */
+				0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000   /* Port 1.2 registers */
+				0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000   /* Port 1.3 registers */
 				0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
 				0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
 				0x82000000 0x2 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
@@ -77,10 +79,18 @@
 				0x81000000 0x3 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO  */
 				0x82000000 0x4 0     MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
 				0x81000000 0x4 0     MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO  */
-				0x82000000 0x9 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
-				0x81000000 0x9 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */
-				0x82000000 0xa 0     MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */
-				0x81000000 0xa 0     MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO  */>;
+
+				0x82000000 0x5 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+				0x81000000 0x5 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */
+				0x82000000 0x6 0     MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */
+				0x81000000 0x6 0     MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO  */
+				0x82000000 0x7 0     MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */
+				0x81000000 0x7 0     MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO  */
+				0x82000000 0x8 0     MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */
+				0x81000000 0x8 0     MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO  */
+
+				0x82000000 0x9 0     MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
+				0x81000000 0x9 0     MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO  */>;
 
 			pcie@1,0 {
 				device_type = "pci";
@@ -106,8 +116,8 @@
 				#address-cells = <3>;
 				#size-cells = <2>;
 				#interrupt-cells = <1>;
-                                ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
-                                          0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &mpic 59>;
 				marvell,pcie-port = <0>;
@@ -150,37 +160,88 @@
 				status = "disabled";
 			};
 
-			pcie@9,0 {
+			pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
-				reg = <0x4800 0 0 0 0>;
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
 				#interrupt-cells = <1>;
-				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
-					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
+				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
-				marvell,pcie-port = <2>;
+				interrupt-map = <0 0 0 0 &mpic 62>;
+				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 26>;
+				clocks = <&gateclk 9>;
 				status = "disabled";
 			};
 
-			pcie@10,0 {
+			pcie@6,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
-				reg = <0x5000 0 0 0 0>;
+				assigned-addresses = <0x82000800 0 0x84000 0 0x2000>;
+				reg = <0x3000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
 				#interrupt-cells = <1>;
-				ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
-					  0x81000000 0 0 0x81000000 0xa 0 1 0>;
+				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
+					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 103>;
-				marvell,pcie-port = <3>;
+				interrupt-map = <0 0 0 0 &mpic 63>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 10>;
+				status = "disabled";
+			};
+
+			pcie@7,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x88000 0 0x2000>;
+				reg = <0x3800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
+					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 64>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 11>;
+				status = "disabled";
+			};
+
+			pcie@8,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x8c000 0 0x2000>;
+				reg = <0x4000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
+					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 65>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 12>;
+				status = "disabled";
+			};
+
+			pcie@9,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+				reg = <0x4800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
+					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 99>;
+				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 27>;
+				clocks = <&gateclk 26>;
 				status = "disabled";
 			};
 		};

arch/arm/boot/dts/at91sam9x5_usart3.dtsi

@@ -11,6 +11,10 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
+	aliases {
+		serial4 = &usart3;
+	};
+
 	ahb {
 		apb {
 			pinctrl@fffff400 {

arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi

@@ -44,8 +44,8 @@
 		gpmc,wr-access-ns = <186>;
 		gpmc,cycle2cycle-samecsen;
 		gpmc,cycle2cycle-diffcsen;
-		vmmc-supply = <&vddvario>;
-		vmmc_aux-supply = <&vdd33a>;
+		vddvario-supply = <&vddvario>;
+		vdd33a-supply = <&vdd33a>;
 		reg-io-width = <4>;
 		smsc,save-mac-address;
 	};

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -215,3 +215,10 @@
 &usbhsehci {
 	phys = <0 &hsusb2_phy>;
 };
+
+&vaux2 {
+	regulator-name = "usb_1v8";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};

arch/arm/boot/dts/omap3-beagle.dts

@@ -61,6 +61,14 @@
 		vcc-supply = <&hsusb2_power>;
 	};
 
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "omap3beagle";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+	};
+
 	gpio_keys {
 		compatible = "gpio-keys";
 
@@ -120,6 +128,12 @@
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
+		};
 	};
 };
 
@@ -178,3 +192,10 @@
 	mode = <3>;
 	power = <50>;
 };
+
+&vaux2 {
+	regulator-name = "vdd_ehci";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};

arch/arm/boot/dts/omap3-igep.dtsi

 /*
- * Device Tree Source for IGEP Technology devices
+ * Common device tree for IGEP boards based on AM/DM37x
  *
  * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
@@ -10,7 +10,7 @@
  */
 /dts-v1/;
 
-#include "omap34xx.dtsi"
+#include "omap36xx.dtsi"
 
 / {
 	memory {
@@ -24,6 +24,25 @@
 		ti,mcbsp = <&mcbsp2>;
 		ti,codec = <&twl_audio>;
 	};
+
+	vdd33: regulator-vdd33 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33";
+		regulator-always-on;
+	};
+
+	lbee1usjyc_vmmc: lbee1usjyc_vmmc {
+		pinctrl-names = "default";
+		pinctrl-0 = <&lbee1usjyc_pins>;
+		compatible = "regulator-fixed";
+		regulator-name = "regulator-lbee1usjyc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>;	/* gpio_138 WIFI_PDN */
+		startup-delay-us = <10000>;
+		enable-active-high;
+		vin-supply = <&vdd33>;
+	};
 };
 
 &omap3_pmx_core {
@@ -48,6 +67,15 @@
 		>;
 	};
 
+	/* WiFi/BT combo */
+	lbee1usjyc_pins: pinmux_lbee1usjyc_pins {
+		pinctrl-single,pins = <
+			0x136 (PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat5.gpio_137 */
+			0x138 (PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat6.gpio_138 */
+			0x13a (PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat7.gpio_139 */
+		>;
+	};
+
 	mcbsp2_pins: pinmux_mcbsp2_pins {
 		pinctrl-single,pins = <
 			0x10c (PIN_INPUT | MUX_MODE0)		/* mcbsp2_fsx.mcbsp2_fsx */
@@ -65,10 +93,17 @@
 			0x11a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
 			0x11c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
 			0x11e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
-			0x120 (PIN_INPUT | MUX_MODE0)		/* sdmmc1_dat4.sdmmc1_dat4 */
-			0x122 (PIN_INPUT | MUX_MODE0)		/* sdmmc1_dat5.sdmmc1_dat5 */
-			0x124 (PIN_INPUT | MUX_MODE0)		/* sdmmc1_dat6.sdmmc1_dat6 */
-			0x126 (PIN_INPUT | MUX_MODE0)		/* sdmmc1_dat7.sdmmc1_dat7 */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			0x12c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc2_dat0.sdmmc2_dat0 */
+			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
 		>;
 	};
 
@@ -78,10 +113,33 @@
 		>;
 	};
 
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x18a (PIN_INPUT | MUX_MODE0)   /* i2c1_scl.i2c1_scl */
+			0x18c (PIN_INPUT | MUX_MODE0)   /* i2c1_sda.i2c1_sda */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x18e (PIN_INPUT | MUX_MODE0)   /* i2c2_scl.i2c2_scl */
+			0x190 (PIN_INPUT | MUX_MODE0)   /* i2c2_sda.i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0x192 (PIN_INPUT | MUX_MODE0)   /* i2c3_scl.i2c3_scl */
+			0x194 (PIN_INPUT | MUX_MODE0)   /* i2c3_sda.i2c3_sda */
+		>;
+	};
+
 	leds_pins: pinmux_leds_pins { };
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
 	clock-frequency = <2600000>;
 
 	twl: twl@48 {
@@ -101,9 +159,16 @@
 #include "twl4030_omap3.dtsi"
 
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
 	clock-frequency = <400000>;
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+};
+
 &mcbsp2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp2_pins>;
@@ -114,11 +179,15 @@
       pinctrl-0 = <&mmc1_pins>;
       vmmc-supply = <&vmmc1>;
       vmmc_aux-supply = <&vsim>;
-      bus-width = <8>;
+      bus-width = <4>;
 };
 
 &mmc2 {
-	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&lbee1usjyc_vmmc>;
+	bus-width = <4>;
+	non-removable;
 };
 
 &mmc3 {

arch/arm/boot/dts/omap3-igep0020.dts

 /*
- * Device Tree Source for IGEPv2 board
+ * Device Tree Source for IGEPv2 Rev. (TI OMAP AM/DM37x)
  *
  * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
@@ -13,7 +13,7 @@
 #include "omap-gpmc-smsc911x.dtsi"
 
 / {
-	model = "IGEPv2";
+	model = "IGEPv2 (TI OMAP AM/DM37x)";
 	compatible = "isee,omap3-igep0020", "ti,omap3";
 
 	leds {
@@ -67,6 +67,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <
 		&hsusbb1_pins
+		&tfp410_pins
+		&dss_pins
 	>;
 
 	hsusbb1_pins: pinmux_hsusbb1_pins {
@@ -85,6 +87,45 @@
 			0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d7.hsusb1_data3 */
 		>;
 	};
+
+	tfp410_pins: tfp410_dvi_pins {
+		pinctrl-single,pins = <
+			0x196 (PIN_OUTPUT | MUX_MODE4)   /* hdq_sio.gpio_170 */
+		>;
+	};
+
+	dss_pins: pinmux_dss_dvi_pins {
+		pinctrl-single,pins = <
+			0x0a4 (PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			0x0a6 (PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			0x0a8 (PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			0x0aa (PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
+			0x0ac (PIN_OUTPUT | MUX_MODE0)   /* dss_data0.dss_data0 */
+			0x0ae (PIN_OUTPUT | MUX_MODE0)   /* dss_data1.dss_data1 */
+			0x0b0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data2.dss_data2 */
+			0x0b2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data3.dss_data3 */
+			0x0b4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data4.dss_data4 */
+			0x0b6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data5.dss_data5 */
+			0x0b8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
+			0x0ba (PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
+			0x0bc (PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
+			0x0be (PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
+			0x0c0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
+			0x0c2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
+			0x0c4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
+			0x0c6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
+			0x0c8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
+			0x0ca (PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
+			0x0cc (PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
+			0x0ce (PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
+			0x0d0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data18.dss_data18 */
+			0x0d2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data19.dss_data19 */
+			0x0d4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data20.dss_data20 */
+			0x0d6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data21.dss_data21 */
+			0x0d8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data22.dss_data22 */
+			0x0da (PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */
+		>;
+	};
 };
 
 &leds_pins {
@@ -174,3 +215,8 @@
 &usbhsehci {
 	phys = <&hsusb1_phy>;
 };
+
+&vpll2 {
+        /* Needed for DSS */
+        regulator-name = "vdds_dsi";
+};

arch/arm/boot/dts/omap3-igep0030.dts

 /*
- * Device Tree Source for IGEP COM Module
+ * Device Tree Source for IGEP COM MODULE (TI OMAP AM/DM37x)
  *
  * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
@@ -12,7 +12,7 @@
 #include "omap3-igep.dtsi"
 
 / {
-	model = "IGEP COM Module";
+	model = "IGEP COM MODULE (TI OMAP AM/DM37x)";
 	compatible = "isee,omap3-igep0030", "ti,omap3";
 
 	leds {

arch/arm/boot/dts/omap3-n900.dts

@@ -125,6 +125,21 @@
 		>;
 	};
 
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk */
+			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd */
+			0x12c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc2_dat0 */
+			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1 */
+			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2 */
+			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3 */
+			0x134 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat4 */
+			0x136 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat5 */
+			0x138 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat6 */
+			0x13a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat7 */
+		>;
+	};
+
 	display_pins: pinmux_display_pins {
 		pinctrl-single,pins = <
 			0x0d4 (PIN_OUTPUT | MUX_MODE4)		/* RX51_LCD_RESET_GPIO */
@@ -358,8 +373,14 @@
 	cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
 };
 
+/* most boards use vaux3, only some old versions use vmmc2 instead */
 &mmc2 {
-	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&vaux3>;
+	vmmc_aux-supply = <&vsim>;
+	bus-width = <8>;
+	non-removable;
 };
 
 &mmc3 {

arch/arm/boot/dts/omap3.dtsi

@@ -82,6 +82,13 @@
 		ranges;
 		ti,hwmods = "l3_main";
 
+		aes: aes@480c5000 {
+			compatible = "ti,omap3-aes";
+			ti,hwmods = "aes";
+			reg = <0x480c5000 0x50>;
+			interrupts = <0>;
+		};
+
 		counter32k: counter@48320000 {
 			compatible = "ti,omap-counter32k";
 			reg = <0x48320000 0x20>;
@@ -260,6 +267,13 @@
 			ti,hwmods = "i2c3";
 		};
 
+		mailbox: mailbox@48094000 {
+			compatible = "ti,omap3-mailbox";
+			ti,hwmods = "mailbox";
+			reg = <0x48094000 0x200>;
+			interrupts = <26>;
+		};
+
 		mcspi1: spi@48098000 {
 			compatible = "ti,omap2-mcspi";
 			reg = <0x48098000 0x100>;
@@ -357,6 +371,13 @@
 			dma-names = "tx", "rx";
 		};
 
+		mmu_isp: mmu@480bd400 {
+			compatible = "ti,omap3-mmu-isp";
+			ti,hwmods = "mmu_isp";
+			reg = <0x480bd400 0x80>;
+			interrupts = <8>;
+		};
+
 		wdt2: wdt@48314000 {
 			compatible = "ti,omap3-wdt";
 			reg = <0x48314000 0x80>;
@@ -442,6 +463,27 @@
 			dma-names = "tx", "rx";
 		};
 
+		sham: sham@480c3000 {
+			compatible = "ti,omap3-sham";
+			ti,hwmods = "sham";
+			reg = <0x480c3000 0x64>;
+			interrupts = <49>;
+		};
+
+		smartreflex_core: smartreflex@480cb000 {
+			compatible = "ti,omap3-smartreflex-core";
+			ti,hwmods = "smartreflex_core";
+			reg = <0x480cb000 0x400>;
+			interrupts = <19>;
+		};
+
+		smartreflex_mpu_iva: smartreflex@480c9000 {
+			compatible = "ti,omap3-smartreflex-iva";
+			ti,hwmods = "smartreflex_mpu_iva";
+			reg = <0x480c9000 0x400>;
+			interrupts = <18>;
+		};
+
 		timer1: timer@48318000 {
 			compatible = "ti,omap3430-timer";
 			reg = <0x48318000 0x400>;

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -246,15 +246,6 @@
 			0xf0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
 		>;
 	};
-};
-
-&omap4_pmx_wkup {
-	led_wkgpio_pins: pinmux_leds_wkpins {
-		pinctrl-single,pins = <
-			0x1a (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk7 */
-			0x1c (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk8 */
-		>;
-	};
 
 	/*
 	 * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
@@ -274,7 +265,7 @@
 		pinctrl-single,pins = <
 			0x38 (PIN_INPUT | MUX_MODE3)		/* gpmc_ncs2.gpio_52 */
 			0x3a (PIN_INPUT | MUX_MODE3)		/* gpmc_ncs3.gpio_53 */
-			0x108 (PIN_OUTPUT | MUX_MODE0)		/* sdmmc5_clk.sdmmc5_clk */
+			0x108 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_clk.sdmmc5_clk */
 			0x10a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_cmd.sdmmc5_cmd */
 			0x10c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat0.sdmmc5_dat0 */
 			0x10e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat1.sdmmc5_dat1 */
@@ -284,6 +275,15 @@
 	};
 };
 
+&omap4_pmx_wkup {
+	led_wkgpio_pins: pinmux_leds_wkpins {
+		pinctrl-single,pins = <
+			0x1a (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk7 */
+			0x1c (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk8 */
+		>;
+	};
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_pins>;

arch/arm/boot/dts/omap4-sdp.dts

@@ -300,12 +300,12 @@
 	wl12xx_pins: pinmux_wl12xx_pins {
 		pinctrl-single,pins = <
 			0x3a (PIN_INPUT | MUX_MODE3)		/* gpmc_ncs3.gpio_53 */
-			0x108 (PIN_OUTPUT | MUX_MODE3)		/* sdmmc5_clk.sdmmc5_clk */
-			0x10a (PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc5_cmd.sdmmc5_cmd */
-			0x10c (PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc5_dat0.sdmmc5_dat0 */
-			0x10e (PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc5_dat1.sdmmc5_dat1 */
-			0x110 (PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc5_dat2.sdmmc5_dat2 */
-			0x112 (PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc5_dat3.sdmmc5_dat3 */
+			0x108 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_clk.sdmmc5_clk */
+			0x10a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_cmd.sdmmc5_cmd */
+			0x10c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat0.sdmmc5_dat0 */
+			0x10e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat1.sdmmc5_dat1 */
+			0x110 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat2.sdmmc5_dat2 */
+			0x112 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat3.sdmmc5_dat3 */
 		>;
 	};
 };

arch/arm/boot/dts/socfpga.dtsi

@@ -245,14 +245,14 @@
 
 					mpu_periph_clk: mpu_periph_clk {
 						#clock-cells = <0>;
-						compatible = "altr,socfpga-gate-clk";
+						compatible = "altr,socfpga-perip-clk";
 						clocks = <&mpuclk>;
 						fixed-divider = <4>;
 					};
 
 					mpu_l2_ram_clk: mpu_l2_ram_clk {
 						#clock-cells = <0>;
-						compatible = "altr,socfpga-gate-clk";
+						compatible = "altr,socfpga-perip-clk";
 						clocks = <&mpuclk>;
 						fixed-divider = <2>;
 					};
@@ -266,8 +266,9 @@
 
 					l3_main_clk: l3_main_clk {
 						#clock-cells = <0>;
-						compatible = "altr,socfpga-gate-clk";
+						compatible = "altr,socfpga-perip-clk";
 						clocks = <&mainclk>;
+						fixed-divider = <1>;
 					};
 
 					l3_mp_clk: l3_mp_clk {

arch/arm/configs/multi_v7_defconfig

@@ -69,6 +69,7 @@ CONFIG_KS8851=y
 CONFIG_SMSC911X=y
 CONFIG_STMMAC_ETH=y
 CONFIG_MDIO_SUN4I=y
+CONFIG_TI_CPSW=y
 CONFIG_KEYBOARD_SPEAR=y
 CONFIG_SERIO_AMBAKMI=y
 CONFIG_SERIAL_8250=y
@@ -133,12 +134,14 @@ CONFIG_USB_GPIO_VBUS=y
 CONFIG_USB_ISP1301=y
 CONFIG_USB_MXS_PHY=y
 CONFIG_MMC=y
+CONFIG_MMC_BLOCK_MINORS=16
 CONFIG_MMC_ARMMMCI=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_ESDHC_IMX=y
 CONFIG_MMC_SDHCI_TEGRA=y
 CONFIG_MMC_SDHCI_SPEAR=y
+CONFIG_MMC_SDHCI_BCM_KONA=y
 CONFIG_MMC_OMAP=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_EDAC=y