GitLab

Corresponding to flashrom svn r838.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

- Add eraseblock definitions
- Use correct eraseblock sizes (the datasheet is a bit ambiguous)
- Use correct probe function
- Fill in probe timing

There is a lot more stuff left to clean up, but at least probe and erase
should work now.

Corresponding to flashrom svn r837.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>

It also changes so -VV will spit out highly verbose messages for
debugging. This is a minimal patch to lessen impact a later patch will
convert current printf messages to the new interface.

Add file that was suppose to be committed with r835.

Corresponding to flashrom svn r836.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

It also changes so -VV will spit out highly verbose messages for
debugging. This is a minimal patch to lessen impact a later patch will
convert current printf messages to the new interface.

Corresponding to flashrom svn r835.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Programmer debug messages during programmer init/shutdown are useful
because they print hardware settings and desired configuration.

They help in getting a quick overview of hardware and software state on
startup and shutdown.

Programmer debug messages during flash chip access are mostly a
distraction in logs and should only be enabled if someone is having
problems which are suspected to stem from a programmer hardware or
programmer software bug. Disable those messages by default, they can be
reenabled by #define COMM_DEBUG in the affected programmer file.

An added benefit is a tremendous size reduction in verbose
probe/read/write/erase logs because only flash chip driver messages
remain. In some cases, logs will shrink from 65 MB to 10 kB or less.

The right(tm) fix would be two different debug levels (DEBUG and SPEW)
and the ability to differentiate between programmer debug messages and
flash chip debug messages. Until the design for the message printing
infrastructure is finished, this is the best stop-gap measure we can
get.

Corresponding to flashrom svn r834.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audioahcked@gmail.com>

And rename them accordingly. For now, main() just calls cli_classic(),
but alternative frontends can be switched in main().
Annotate remaining help texts with CLI dependency inside flashrom.c with
a FIXME comment.

Now people can go and create different frontends and be happy. Please
note that any other frontend will have to sort of duplicate the probing
code in cli_classic.c. Refactoring that part of the code is possible,
but not easy because we still want to print instructive help messages
for users.

Corresponding to flashrom svn r833.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>

Corresponding to flashrom svn r832.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

- replace the hand written serial input flush routine with the termios one.
- serialport_discard_read isn't necessary anymore - it just wrapped
  sp_flush_incoming with no extra value.
- serialport_read and serialport_write would misbehave if read or write
  didn't process everything in one go.
- sp_flush_incoming should be #define'd out for FAKE_COMMUNICATION like
  serialport_discard_read was

Corresponding to flashrom svn r831.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Sean Nelson <audiohacked@gmail.com>

While at it, also rename a few functions to make it obvious
that they are generic and not specific to the Bus Pirate.

Corresponding to flashrom svn r830.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>

Some programmers (most notably FT2232SPI) use fallback_* and noop_*,
but those functions lived inside internal.c and were unavailable if no
PCI-based programmers were compiled in.

Move those functions to the new file programmer.c. Thanks to Patrick
Georgi for finding this.

Corresponding to flashrom svn r829.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>

The patch converts jedec functions into mask-based generics which can
be used for many chip provided the only changes are the addresses are
converted from 0x5555/0x2AAA to 0x555/0x2AA or similar.

The patch mostly changes jedec.c, but a few other files are changed
because they use the jedec functions within their own functions.

The patch also adds a copyright line to flashchips.c because of my
recent work in converting AMD and Atmel chips to use struct erase_block.

Corresponding to flashrom svn r828.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Drop usage information that is already mentioned in the man page.

Corresponding to flashrom svn r827.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Fixes wrong detection of area decoded to the FWH interfaces.

Corresponding to flashrom svn r826.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r825.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

It just splits $(OBJS) in Makefile into separate lists for Programmer,
Chip, and CLI related files/objects. This should help later on figuring
out where files may go for a libflashrom library.

Corresponding to flashrom svn r824.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Libpci is no longer required to build flashrom and will not be checked
for if no PCI code is needed for the selected programmers.
libftdi is no longer checked for if FT2232 support is not selected.

With this patch, it is possible to build on pretty much every OS out
there (including Windows) without altering the Makefile.
Some gcc versions may need a CFLAGS override for a warning in
dummyflasher.c, though.

Corresponding to flashrom svn r823.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Idwer Vollering <vidwer@gmail.com>

Move that function to udelay.c and compile internal.c only if really
needed. physmap.c is only needed if the programmer is internal or a PCI
card. Make its compilation conditional.

Corresponding to flashrom svn r822.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Idwer Vollering <vidwer@gmail.com>

Add a generic programmer list output function to be used by alternative
frontends. The interface between main() and doit is a hack and should
get a clean design, but for now it serves the purpose of shortening
main() by 120 lines. The rest of main() needs to be refactored a bit
more before moving main() away.

Corresponding to flashrom svn r821.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>

Corresponding to flashrom svn r820.
Signed-off-by: Raúl Soriano <GatoLoko@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

AMIC_A29002B
AMIC_A29002T
EN_29F002B
EN_29F002T
MBM29F004BC
MBM29F004TC
MBM29F400BC
MBM29F400TC
MX_25L3205
MX_25L6405
MX_29F002B
MX_29F002T

Add block erasers for m29f400bt and mx29f002.
Change programmer delays from 2 seconds to 10us in mx29f002 and am29f040b.

Corresponding to flashrom svn r819.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

SST25VF040.REMS, SST25VF040B, SST25VF040B.REMS, SST25VF080B,
SST25VF016B, SST25VF032B

Corresponding to flashrom svn r818.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>

AT25DF021, AT25DF041A, AT25DF081, AT25DF161, AT25DF321, AT25DF321A,
AT25DF641, AT25F512B, AT25FS010, AT25FS040, AT26DF041, AT26DF081A,
AT26DF161, AT26DF161A, AT26F004, AT29C512, AT29C010A, AT29C020,
AT29C040A, AT49BV512, AT49F002(N), AT49F002(N)T

A possible future patch would to add spi_block_erase_d7 to spi.c as an 
alternate to spi_block_erase_20. Only some SPI chips support d7.

Corresponding to flashrom svn r817.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r816.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Fraser Hanson <fraser.hanson@gmail.com>

Only done for VT8237R (possibly needed for VT8237 too), VT8235 does
not need this (even if the original bios does so: Asus A7V8X-MX SE,
MSI KT4V were verified).

This then opens a floodgate of cleanups in the board enables.
* EPIA SP board enable vanishes, taking EPIA CN match with it.
* Asus A7V8X-MX/Tyan S2498 board enable then equals
  w836xx_memw_enable_2e
* AOpen vKM400Am-S board enable then equals it8705_rom_write_enable
* Epia M board enable becomes via_vt823x_gpio15_raise
* Epia N board enable becomes via_vt823x_gpio9_raise
* Asus M2V-MX board enable becomes via_vt823x_gpio5_raise
* vt823x_gpio_set becomes via_vt823x_gpio_set, and now detects ISA
  bridge itself, in concordance with intel ich and nvidia mcp gpio.

Corresponding to flashrom svn r815.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r814.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

We could run it after chipset enable, but it definitely has to happen
before board enable because the board enable usually accesses the
SuperI/O. With this patch, it is possible to add a struct superio to the
board enable table for more accurate matching in case subsystem IDs are
ambiguous. This patch focuses on the generic infrastructure aspect and
on support for IT8712F/IT8716F.

Thanks go to Adrian Glaubitz and Ward Vandewege for testing.

Corresponding to flashrom svn r813.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Adrian Glaubitz <glaubitz@physik.fu-berlin.de>

Am29F010A/B
Am29F002(N)BB
Am29F002(N)BT
Am29F016D
Am29F040B
Am29F080B
Am29LV040B
Am29LV081B
A29040B
Pm29F002T
Pm29F002B

Change function signature of Am29 erase functions and JEDEC chip erase
to be usable with block_erasers.

Corresponding to flashrom svn r812.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Reported by Sean Nelson.

Corresponding to flashrom svn r811.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

- CK804, MCP04, MCP2 use the isa bridges..
- Newer nvidia mcp's do use the smbus controllers (Found by
  Michael Karcher).
- gpio line check breaks EPoX EP-8RDA3+, and should be wider.

Corresponding to flashrom svn r810.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Corresponding to flashrom svn r809.
Signed-off-by: Adam Jurkowski <adam.jurkowski@kontron.pl>
Acked-by: Luc Verhaegen <libv@skynet.be>

The nulled second set of subsystem ids is correct, and this seems
to be a unique match.

Corresponding to flashrom svn r808.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: spirals <spirals@eircom.net>

If the JEDEC Toggle Bit algorithm needs more than 2^20 loops, it is a
good sign we should have used delays between toggle bit reads.

Tell the user about this. 2^20 loops need roughly a second depending on
flash bus speed. One reason for excessive loops can be a slow operation
like erase.

The Winbond W39V040C requires a 50 ms delay between toggle bit reads
during erase according to the datasheet. Turns out a 2 ms delay is
sufficient. Use a safety factor of 4 and default all erase operations
to 8 ms delay between toggle reads. This is short enough not to have
a substantial negative impact on erase times, and should improve
reliability.

This patch addresses the excessive toggle behaviour (observed on some
non-Winbond chips) and the toggle delay requirement (Winbond W39V040C).

Corresponding to flashrom svn r807.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Javier Ortega Conde (aka Malkavian) <malkavian666@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

- Detect max FWH size for Intel
  631xESB/632xESB/3100/ICH6/ICH7/ICH8/ICH9/ICH10.
- Move IDSEL override before decode size checking for the chipsets
  listed above or flashrom will complain based on old values.
- Adjust supported flash buses for the chipsets listed above (none of
  them supports LPC or Parallel).
- Detect max parallel size for AMD/National Semiconductor CS5530.
- Adjust supported flash buses for CS5530/CS5530A.
- Set board-specific max decode size for Elitegroup K7VTA3.
- Set board-specific max decode size for Shuttle AK38N.

Corresponding to flashrom svn r806.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Probe_jedec() checks the delay value and issues programmer_delay based
on the value except for delays between single chip_writeb. If a chip has
zero probe_delay, delays between chip_writeb should be skipped as well.

Corresponding to flashrom svn r805.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r804.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

The function intel_piix4_gpo_set includes proper gpo pin checking, and
gpo pin enables when necessary.

This is a leftover from soyo SY-6BA+III code that turned out to be
unnecessary, but still used for the epox ep-bx3 board enable which it
cleans up and clarifies.

Difference to old code:
* typical bios delay io port 0xEB now never gets touched.
* pci config byte 0xB0 was not altered before.

Corresponding to flashrom svn r803.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

This is needed on NetBSD and probably other non-Linux platforms.

Corresponding to flashrom svn r802.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r801.
Signed-off-by: Zachary O Dillard <teathief@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

I found this bug during a code review. A consistency check for
eraseblock definitions has been merged as well.

Corresponding to flashrom svn r800.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>

This patch is only the first step, but it hopefully will make working
with the code and especially porting to new platforms easier.

Subsequent patches should move #includes for the newly created files
hwaccess.h and chipdrivers.h from flash.h to the files which need them.
Programmers should live in a separate header file as well.
Tested-by: Idwer Vollering <vidwer@gmail.com>

Corresponding to flashrom svn r799.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>