GitLab

Drop no longer needed MAX macro, we have a max() function.

Corresponding to flashrom svn r601.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

FTDI support is autodetected during compilation.

Paul writes:
There are certainly possible improvements: The code has hard-coded
values for which interface of the ftdi chip to use (interface B was
chosen because libftdi seems to have trouble with A right now), what
clock rate use for the SPI interface (I've been running at 30Mhz, but
the patch sets it to 10Mhz), and possibly others. I think this means
that per-programmer options might be a good idea at some point.

Carl-Daniel writes:
There is one additional FIXME comment in the code, but AFAICS that
problem is not solvable with current libftdi.

Corresponding to flashrom svn r598.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

That means you can tell flashrom to read exactly bytes 12345-56789
(start 12345, length 44445) and it will not fetch a single byte more.

Uwe tested this on one LPC, one SPI, and one parallel flash board.

Corresponding to flashrom svn r596.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

And even when it checks if the erase worked, the result of that check is
often ignored.

Convert all erase functions and actually check return codes
almost everywhere.
Check inside all erase_* routines if erase worked, not outside.
erase_sector_jedec and erase_block_jedec have changed prototypes to
enable erase checking.

Uwe successfully tested LPC on an CK804 box and SPI on some SB600 box.

Corresponding to flashrom svn r595.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Flash.h not only contains function prototypes and general settings, it
also has a huge chunk of chip and vendor IDs in the middle.

Split them out into a separate flashchips.h and adjust #include wherever
needed.

Corresponding to flashrom svn r594.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Urja Rannikko <urjaman@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

Fix the vendor ID of EN25B05, EN25B10, EN25B20, EN25B40, EN25B80,
EN25B16, EN25B32, EN25B64 EN25F40, EN25F80, EN25F16.

Add support for EN25P05, EN25P10, EN25P20, EN25P40, EN25P80, EN25P16,
EN25P32, EN25P64 EN25D16 EN25F05, EN25F10, EN25F20, EN25F32

Corresponding to flashrom svn r592.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

I sucessfully tested all operations on a Pm29F002T chip. The Pm29F002B is
untested but I assume it should also work.

Corresponding to flashrom svn r590.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

This was partly due to a design problem in the abstraction layer.

There should be exactly two different functions for reading SPI chips:
- memory mapped reads
- SPI command reads.

Each of them should be contained in a separate function, optionally
taking parameters where needed.

This patch solves the problems mentioned above, shortens the code and
makes the code logic a lot more obvious.

Since open-coding the min() function leads to errors, include it in this
patch as well.

Corresponding to flashrom svn r589.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>

Add timing info to some flash chips.

Corresponding to flashrom svn r584.
Signed-off-by: Mateusz Murawski <matowy@tlen.pl>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r583.
Signed-off-by: Paul Fox <pgf@laptop.org>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Some IDs were already in flash.h. EN25B05 EN25B10 EN25B20 EN25B40
EN25B80 EN25B16 EN25B32 EN25B64 EN25F40 EN25F80 EN25F16

EN25P* are supported as well, but they seem to be identical to EN25B.

Corresponding to flashrom svn r580.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>

Add chip_{read,write}n to the external flasher infrastructure which
read/write n bytes at once.

Fix a few places where the code used memcpy/memcmp although that is
strictly impossible with external flashers.
Place a FIXME in the layout.c code because usage is not totally clear
and needs to be fixed to support external flashers.

As a nice side benefit, we get a noticeable speedup for builtin flash
reading which is now a memcpy() of the full flash area instead of a
series of single-byte reads.

Corresponding to flashrom svn r579.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Urja Rannikko <urjaman@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Add external programmer delay functions so external programmers can
handle the delay on their own if needed.

Corresponding to flashrom svn r578.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Urja Rannikko <urjaman@gmail.com>

This eliminates the conflicting delay requirements for old and new chips
with the same probing sequence.

Corresponding to flashrom svn r569.
Signed-off-by: Maciej Pijanka <maciej.pijanka@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Also do some random cleanups while I'm at it.

Corresponding to flashrom svn r567.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Also, add Atmel AT29C512 support.

Both are tested on hardware by Maciej Pijanka.

Corresponding to flashrom svn r566.
Signed-off-by: Maciej Pijanka <maciej.pijanka@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Corresponding to flashrom svn r564.
Signed-off-by: Mateusz Murawski <matowy@tlen.pl>
Acked-by: FENG Yu Ning <fengyuning1984@gmail.com>

The syntax is explained in the man page.
Example: flashrom -p dummy=lpc,fwh

Tested, works perfectly. ;-)

As a nice benefit, it allows easy testing of the "probe only compatible
flashes" patch.

Corresponding to flashrom svn r559.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

This is a fast way to test if a IT87xx board_enable() would work.

Corresponding to flashrom svn r557.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Harald Gutmann <harald.gutmann@gmx.net>

Right now, the annotation only differentiates between SPI and non-SPI.
Anyone who knows more about a specific flash chip should feel free to
update it.

The existing flashbus variable was abused to denote the SPI controller
type. Use an aptly named variable for that purpose.

Once this patch is merged, the chipset/programmer init functions can set
supported flash chip types and flashrom can automatically select only
matching probe/read/erase/write functions. A side benefit of that will
be the elimination of the Winbond W29EE011 vs. AMIC A49LF040A conflict.

Corresponding to flashrom svn r556.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Erase & write support wont be this easy - the chips need 12V Vpp
(needs a hardware hack or a supporting mb) and they have a very weird
layout and are old.

Corresponding to flashrom svn r555.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

 - Add explicit installation instructions in the README.

 - Code cleanups, coding style fixes, drop dead code.

 - Drop duplicate board listings from -L output (some boards were explicitly
   recorded in boards_ok[] _and_ implicitly via the board-enables table.

 - Add MS-xxxx numbers to MSI boards where we can find that info.

 - Fix typo, "K8T Neo2" should have been "K8T Neo2-F" actually, at least
   according to the comment of w83627thf_gpio4_4_raise_2e() which says
   "Suited for: MSI K8T Neo2-F".

Corresponding to flashrom svn r554.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Corresponding to flashrom svn r550.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>

We had duplicated code under different names and even open-coded some
functions in some places.

wbsio_read/regval -> sio_read wbsio_write/regwrite -> sio_write
wbsio_mask -> sio_mask

board_biostar_p4m80_m4 now uses existing IT87 functions.

Corresponding to flashrom svn r547.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Luc Verhaegen <libv@skynet.be>

Corresponding to flashrom svn r531.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

 - Document new 'satasii' programmer in -L output and manpage.

 - Drop PCI_IO_BASE_ADDRESS, pci.h has such #defines already.

 - Beautify flashrom output and make it more consistent.
 
 - Same for the 'make' output (reordered some $CC parameters).
   Build-tested on i386, shouldn't break any builds, I think.

 - Some variable renaming and other cosmetic fixes.

Corresponding to flashrom svn r529.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

It was easy because

1) flashrom has now nice API 2) documentation is public on the web site

Corresponding to flashrom svn r527.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Some MMIO accesses used volatile, others didn't (and risked
non-execution of side effects) and even with volatile, some accesses
looked dubious.

Since the MMIO accessor functions and the onboard flash accessor
functions are functionally identical (but have different signatures),
make the flash accessors wrappers for the MMIO accessors.

For some of the conversions, I used Coccinelle. Semantic patch follows:

@@ typedef uint8_t; expression a; volatile uint8_t *b; @@ - b[a] + *(b
+ a) @@ expression a; volatile uint8_t *b; @@ - *(b) |= (a); + *(b) =
*(b) | (a); @@ expression a; volatile uint8_t *b; @@ - *(b) = (a); +
mmio_writeb(a, b); @@ volatile uint8_t *b; @@ - *(b) + mmio_readb(b) @@
type T; T b; @@ ( mmio_readb | mmio_writeb ) (..., - (T) - (b) + b )

Corresponding to flashrom svn r524.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Uwe tested read, write, erase with this patch on a random board to make
sure nothing breaks.
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

 - Supported out of the box (no flash enables required)

 - Verifiably not yet working (unknown flash enable)

Also, move some structs to flash.h in preparation for later wiki
output support.

Corresponding to flashrom svn r523.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

They serve pretty much no purpose, compilers can optimize pretty much
all of what we might mark as inline anyway, _and_ inlines are not
enforced in any way by the compiler either. They're totally unneeded.
Kill them.

Corresponding to flashrom svn r522.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Build-tested on 32bit x86.

Corresponding to flashrom svn r521.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

This is tested on hardware.

Also, add initial support for the Atmel AT29C010A chip (which I inserted
in a 3COM 3C90xB card for testing). It can be detected, read works,
erase works, but write will need some additional code (will post in
another patch later).

Corresponding to flashrom svn r520.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Use chipaddr instead of volatile uint8_t * because when we access chips
in external flashers, they are not accessed via pointers at all.

Benefits: This allows us to differentiate between volatile machine
memory accesses and flash chip accesses. It also enforces usage
of chip_{read,write}[bwl] to access flash chips, so nobody will
unintentionally use pointers to access chips anymore. Some unneeded
casts are removed as well. Grepping for chip operations and machine
memory operations doesn't yield any false positives anymore.

Compile tested on 32 bit and 64 bit Linux.

Corresponding to flashrom svn r519.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

The emulation works by splitting 32 bit accesses into 16 bit accesses
and 16 bit accesses into to 8 bit accesses. That way, external flashers
can mix and match the amount of emulation they need.

Corresponding to flashrom svn r517.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Move the reusable PCI specific parts into pcidev.c, they'll be usable
for other NIC code (Realtek, VIA, ...) and also for SATA/IDE controller
cards as external programmers (for every PCI device which can program
EEPROMs basically).

Also add print_supported_pcidevs() to show the supported PCI devices
(currently only NICs, soon more) in the 'flashrom -L' output.

Corresponding to flashrom svn r515.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r512.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Factor out portable iopl()-style code into a global function which all
programmers can use, add missing close() call.

Corresponding to flashrom svn r511.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Add support for users to specify a certain NIC via PCI bus:slot.func
notation, in case there are multiple NICs in one system.

Usage: flashrom -p nic3com=bb:ss.f

Corresponding to flashrom svn r510.
Signed-off-by: Christian Ruppert <spooky85@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Does not support reading or writing the fake chip yet.

flashrom --programmer dummy
also enables the dummy SPI controller driver.

Testing the dummy SPI driver revealed a RDID debug printing bug in the
SPI core. Fix that as well.

Corresponding to flashrom svn r507.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Among others, I have seen the following problems: - The SPI opcode is
not supported by the controller. ICH-style controllers exhibit this if
SPI config is locked down. - The address in in a prohibited area. This
can happen on ICH for any access (BBAR) and for writes in chipset write
protected areas. - There is no SPI controller.

Introduce separate error codes for unsupported opcode and prohibited
address.

Add the ability to adjust REMS and RES addresses to the minium supported
read address with the help of spi_get_valid_read_addr(). That function
needs to call SPI controller specific functions like reading BBAR on
ICH.

Corresponding to flashrom svn r500.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>