GitLab

Programmer specific functions are of absolutely no interest to any file
except those dealing with programmer specific actions (special SPI
commands and the generic core).

The new header structure is as follows (and yes, improvements are
possible):
flashchips.h  flash chip IDs
chipdrivers.h  chip-specific read/write/... functions
flash.h  common header for all stuff that doesn't fit elsewhere
hwaccess.h hardware access functions
programmer.h  programmer specific functions
coreboot_tables.h  header from coreboot, internal programmer only
spi.h SPI command definitions

Corresponding to flashrom svn r1112.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Change the nicnatsemi address mask to use MA0-MA16 and set the maximum
decode size to 128KB.

Corresponding to flashrom svn r1095.
Signed-off-by: Andrew Morgan <ziltro@ziltro.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Constify variables where possible.
Initialize programmer-related variables explicitly in programmer_init to
allow running programmer_init from a clean state after
programmer_shutdown.
Prohibit registering programmer shutdown functions before init or after
shutdown.
Kill some dead code.
Rename global variables with namespace-polluting names.
Use a previously unused locking helper function in sst49lfxxxc.c.

This is needed for libflashrom.

Effects on the binary size of flashrom are minimal (300 bytes
shrinkage), but the data section shrinks by 4384 bytes, and that's a
good thing if flashrom is operating in constrained envionments.

Corresponding to flashrom svn r1068.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

The logic was incorrect in one place which had && instead of ||. Move
the board info #define B to the file where it is used.

Corresponding to flashrom svn r1035.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

The required "-m" options were not in the wiki output due to a mistake
that I think I introduced recently.

Corresponding to flashrom svn r1027.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Also, merge the tables in the output, i.e. there's only one table which
contains both known-good and known-bad/untested boards.

Corresponding to flashrom svn r1024.
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

CONFIG_FT2232SPI (makefile config option)
FT2232_SPI_SUPPORT (#define)
ft2232spi (programmer name)
ft2232_spi.c (programmer file)

Use CONFIG_* with underscores for makefile config options and #defines
and kill the useless _SUPPORT idiom.
Use lowercase names with underscores for programmer names and programmer
files.

With this, you can run "grep -i ft2232_spi" and find everything related
to the ft2232_spi driver. Same applies to all other programmers.

Corresponding to flashrom svn r1023.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

- x86/x86_64 (little endian)
- PowerPC (big endian)
- MIPS (big+little endian)

No changes to programmer specific code. This means any drivers with MMIO
access will _not_ suddenly start working on big endian systems, but with
this patch everything is in place to fix them.

Compilation should work on all architectures listed above for all
drivers except nic3com and nicrealtek which require PCI Port IO which is
x86-only for now.

To compile without nic3com and nicrealtek, run
make distclean
make CONFIG_NIC3COM=no CONFIG_NICREALTEK=no

Thanks to Misha Manulis for testing early versions of this patch on
PowerPC (big endian) with the satasii programmer.
Thanks to Segher Boessenkool for design review and for helping out with
compiler tricks and pointing out that we need eieio on PowerPC.
Thanks to Vladimir Serbinenko for compile testing on MIPS (little
endian) and PowerPC (big endian) and for runtime testing on MIPS (little
endian).
Thanks to David Daney for compile testing on MIPS (big endian).
Thanks to Uwe Hermann for compile and runtime testing on x86_64.

DO NOT RUN flashrom ON NON-X86 AFTER APPLYING THIS PATCH!
This patch only provides the infrastructure, but does not convert any
drivers, so flashrom will compile, but it won't do the right thing on
non-x86 platforms.

Corresponding to flashrom svn r1013.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Misha Manulis <misha@manulis.com>
Acked-by: Vladimir 'phcoder/φ-coder' Serbinenko <phcoder@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>

 - Add missing entries for 'flashrom -L' output and wiki output.

 - Add missing entries in the manpage.

 - nicrealtek.c: Coding style fixes and cosmetics.

Corresponding to flashrom svn r1011.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

 - Use '?3' wiki template (light greenish, not gray) for untested stuff.
 
 - Reduce page width a bit to improve readability on smaller screens.
 
 - Generalize some functions a bit (pass in how many columns to generate).
 
 - Mark untested board-enables as such (were incorrectly marked "OK" so far).
 
 - Drop some useless 'valign=top' entries.
 
 - Make a few more functions 'static' while we're at it.

Corresponding to flashrom svn r1009.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Change the command line interface to make file names positional.
Add more sanity checks to the command line parser.

Corresponding to flashrom svn r998.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Corresponding to flashrom svn r993.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Tom Brand <worntreads@sbcglobal.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

PMC Pm39LV010:
 See http://www.coreboot.org/pipermail/flashrom/2010-March/002711.html
 Thanks to Tim Small for reporting!

Supermicro X8DTT-F:
 See http://www.coreboot.org/pipermail/flashrom/2010-March/002707.html
 Thank to Taylan Develioglu for testing!

Gigabyte GA-965P-DS4:
 See http://www.coreboot.org/pipermail/flashrom/2010-March/002426.html
 Thanks to Michal Andrzejczak for reporting!

Tyan Tempest i5000PW:
 See http://www.coreboot.org/pipermail/flashrom/2010-February/002358.html
 Thanks to Rob Lazzurs for reporting!

PCEngines WRAP.2E:
 See http://www.coreboot.org/pipermail/flashrom/2010-February/002187.html
 Thanks to Vincenzo Caruso for testing!

Asus P5B:
 This board has been reporting as working (for r710/0.9.1) in:
 http://www.coreboot.org/pipermail/flashrom/2010-February/002170.html
 Thanks to Patrice Levesque for testing!

MSI 7312 (K9MM-V) + W39V040B:
 See http://www.coreboot.org/pipermail/flashrom/2010-February/002159.html
 Thanks to David Mears for testing!

Probe + Read on SST49LF080A:
 See http://www.coreboot.org/pipermail/flashrom/2010-February/002095.html


 Thanks to Peter Lemenkov for testing!

Finally:
 remove Asus A7V8X-X from "boards_ok", as this table is meant only for
 boards not needing a board enable.

Corresponding to flashrom svn r984.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

See http://www.coreboot.org/pipermail/flashrom/2010-March/002451.html



Thanks to Paweł Stawicki for reporting!

Corresponding to flashrom svn r980.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

FD37: http://www.coreboot.org/pipermail/flashrom/2010-March/002440.html
K9A2: http://www.coreboot.org/pipermail/flashrom/2010-March/002433.html



Thanks to Sylvain BERTRAND for reporting!

Corresponding to flashrom svn r979.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

W49F002U: http://www.coreboot.org/pipermail/flashrom/2010-March/002469.html
EN29F002: http://www.coreboot.org/pipermail/flashrom/2010-March/002480.html



Block erase was broken, chip erase worked, block erase is fixed in r934 but
has not been tested since.

Thanks to Guy Lacroix for reporting!

Corresponding to flashrom svn r978.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

See http://www.coreboot.org/pipermail/flashrom/2010-March/002501.html


Thanks to Konstantin Matuschek for reporting.

Corresponding to flashrom svn r977.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

The Asus A8NE-FM/S does exist, you find original ASUS pdf manuals in the
internet, but seems to be an OEM board that is not documented on the
Asus page.

A lot of MSI boards are OEM boards that have no page at the MSI site...

This patch also adds links in the Wiki for boards from the board enable
table.

Corresponding to flashrom svn r976.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Abit VT6X4 / W29C020C: See
  http://www.coreboot.org/pipermail/flashrom/2010-March/002730.html
  Fixes typo in comment and marks board-enable as tested (the flashrom
  running on that machine was patched with the board enable that got
  in later).

Asus A7V133 / Atmel AT29C010A: See
  http://www.coreboot.org/pipermail/flashrom/2010-March/002729.html


  Adding "erase" to tested as there is only one erase function.

Corresponding to flashrom svn r975.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Lspci/flashrom/superiotool at
http://www.coreboot.org/pipermail/flashrom/2010-March/002579.html



Corresponding to flashrom svn r947.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

This board has a supported chipset and a supported bios, but it's
connected indirectly through IT8716 and not recognized.

Corresponding to flashrom svn r935.
Signed-off-by: Raúl Soriano <GatoLoko@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

I have an ASUS A7V8X-X, the BIOS programming requires a write-enable. It
has an IT8712F, just like the A7V600-X.

Corresponding to flashrom svn r929.
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

We don't need to duplicate OK and NT as PCI_OK and PCI_NT if the symbols
are already there (defined for the chipset enable table).

Corresponding to flashrom svn r911.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

It's disabled by default. The current status is detailed at:
http://www.flashrom.org/pipermail/flashrom/2010-January/001828.html



Corresponding to flashrom svn r908.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

The board doesn't need a board-enable, writing works out of the box.

Also, the board can only decode 256KB. I verified this by writing a 512KB
image of random bytes (which fails), whereas 256KB of random bytes can be
written correctly.

Corresponding to flashrom svn r887.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Thanks to Michael Karcher for noticing.

Corresponding to flashrom svn r863.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Corresponding to flashrom svn r801.
Signed-off-by: Zachary O Dillard <teathief@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

 - AsRock K8S8X (reported by Adrian Glaubitz <adrian.glaubitz@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2009-November/000937.html

 - ASUS K8V-X SE (reported by Adrian Glaubitz <adrian.glaubitz@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2009-November/000965.html

 - DFI Blood-Iron P35 T2RL (reported by Erno Vaurio <ernovaur@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2009-November/001059.html



Corresponding to flashrom svn r791.
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

To prepare for libflashrom I wanted to make the main loop more readable and more correct and factor out stuff which can be useful in libflashrom.

- Factor out printing of supported devices to print.c.
- Adjust name of wiki printing function to fit the pattern.
- Abort if the user specified --verify and --noverify at the same time.
- Check for extra parameters which don't fit commandline syntax.

Corresponding to flashrom svn r766.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

Add a note for ASUS M2N-E.
Change "iff" to "if". Most people don't understand what "iff" means and
the meaning of both words is close enough to hopefully give users the
right idea.

Corresponding to flashrom svn r763.
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r750.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

 - MSI MS-6153 (reported by Uwe Hermann <uwe@hermann-uwe.de>)
   Tested by me on hardware. The board decodes max. 256 KB.

 - MSI MS-6156 (reported by Uwe Hermann <uwe@hermann-uwe.de>)
   Tested by me on hardware. The board decodes max. 256 KB.

Also, fix Dell PowerEdge 1850 name and add some more board URLs.

Corresponding to flashrom svn r749.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Corresponding to flashrom svn r735.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

 - ASUS M3A78-EM (reported by Christian Heinz <christian.ch.heinz@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2009-September/000629.html
 
 - MSI MS-7368 (K9AG Neo2-Digital) (reported by Joshua Roys <roysjosh@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2009-September/000632.html

 - GIGABYTE GA-MA770T-UD3P (reported by Kevin Sopp <baraclese@googlemail.com>)
   http://www.flashrom.org/pipermail/flashrom/2009-September/000529.html


   
 - Elitegroup P6VAP-A+
   Tested by Uwe Hermann <uwe@hermann-uwe.de> on hardware. Maximum supported
   chip size in this board is 256 KB.
   
Small changes in print.c were required to adjust for longer board names.

Corresponding to flashrom svn r734.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

This is useful for libflashrom (you don't need wiki output in a coreboot
payload).

Wiki output is now disabled by default. If you want to enable it, run
make CONFIG_PRINT_WIKI=yes

Corresponding to flashrom svn r725.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

Example make commandline if you want only internal programmers:
make CONFIG_FT2232SPI=no CONFIG_SERPROG=no CONFIG_NIC3COM=no
CONFIG_SATASII=no CONFIG_DRKAISER=no CONFIG_DUMMY=no

Of course, all of the CONFIG_* symbols can be mixed and matched as
needed. CONFIG_FT2232SPI is special because even if it is enabled, make
will check if the headers are available and skip it otherwise.

Corresponding to flashrom svn r724.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

This is a followup to r705.

Corresponding to flashrom svn r707.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Luc Verhaegen <libv@skynet.be>

Update bad board list and remove boards where either the chipset is
not supported (not a board issue) or where we have no report in the
archives.

Corresponding to flashrom svn r703.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Marked as OK:

 - ASUS A8V Deluxe (reported by Joachim Ernst <Joachim.Ernst@web.de>)
   http://www.flashrom.org/pipermail/flashrom/2009-August/000448.html
   Tested with r701.

 - ASUS P5L-MX (reported by Vasiliy Vylegzhanin <6vasia@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2009-August/000446.html
   Tested with v0.9.0.

 - Abit Fatal1ty F-I90HD (reported by Joachim Ernst <joachim.ernst@web.de>)
   http://www.flashrom.org/pipermail/flashrom/2009-August/000435.html

 - Trigem Lomita (reported by Udu Ogah <putlinuxonit@gmail.com>)
   Tested with r695.

 - GIGABYTE GA-MA790GP-DS4H (reported by Ralph Loader <suckfish@ihug.co.nz>)
   http://www.flashrom.org/pipermail/flashrom/2009-August/000414.html
   http://www.flashrom.org/pipermail/flashrom/2009-August/000417.html

 - GIGABYTE GA-MA78GPM-DS2H (reported by
                             Erik Haugen Bakke <erik_hb_mlist@yahoo.com.au>)
   http://www.flashrom.org/pipermail/flashrom/2009-August/000329.html



Corresponding to flashrom svn r702.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Mark the following boards as OK (no board-enable needed):

 - Tyan S2466 (reported by Oliver Niesner <oli@servebbs.net>)
   http://www.flashrom.org/pipermail/flashrom/2009-August/000211.html



Mark the following boards as non-working for now:

 - ASRock K7VT4A+ (reported by Udu Ogah <putlinuxonit@gmail.com>)
   Chipset detect, but no chip.
 
 - ASUS M2N68 (reported by Udu Ogah <putlinuxonit@gmail.com>)
   Chipset detect, but no chip.
 
 - ASUS A7V600-X (reported by Udu Ogah <putlinuxonit@gmail.com>)
   Chipset and chip detected, writes don't work. Board-enable required.

Also, add some missing board URLs and fix incorrect board names.

Corresponding to flashrom svn r695.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>