GitLab

Interestingly enough, this board's enable looked more like
enable_flash_nvidia_nforce2 than enable_flash_ck804; it whacked
0x92, not 0x88. But according to the lspci, 0x92 is already 0.

Tested successfully on hardware:
 http://www.flashrom.org/pipermail/flashrom/2010-August/004568.html
 http://www.flashrom.org/pipermail/flashrom/2010-September/004575.html



Corresponding to flashrom svn r1154.
Signed-off-by: Joshua Roys <roysjosh@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Many thanks to Michael Karcher for reverse engineering this.

lspci/superio output:
http://www.flashrom.org/pipermail/flashrom/2010-August/004475.html



Corresponding to flashrom svn r1146.
Signed-off-by: Mattias Mattsson <vitplister@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

lspci/superiotool:
  http://www.coreboot.org/pipermail/flashrom/2010-August/004440.html



Corresponding to flashrom svn r1143.
Signed-off-by: Mattias Mattsson <vitplister@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

This patch changes the intel_piix4_gpo_set() function to always check
the GENCFG and XBCS registers for the availability of the
requested GPO line before raising/lowering it and fails otherwise. It
makes no attempt to bypass the values in these configuration
registers.

The old flashrom code did consider it safe to reprogram (multiplexed)
GPO:s 22-26 without checking the value of the controlling register
(GENCFG). I do not really know why.

I have tested this patch on an Asus P2B-N (needs GPO18 low) and MSI
MS-6163 Pro (needs GPO14 high).

The information for these registers are from the Intel "82371AB
PCI-TO-ISA / IDE XCELERATOR (PIIX4)" datasheet available here:
http://www.intel.com/design/intarch/datashts/29056201.pdf



Corresponding to flashrom svn r1142.
Signed-off-by: Mattias Mattsson <vitplister@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

- There are number of boards that have board-enables in board-enable.c but
  have no corresponding entry in print.c (with or without URL doesn't matter)
  and thus appear neither in the "flashrom -L" list of boards nor in the
  wiki output. Fix this by adding entries for them in print.c.

   - abit AN-M2
   - abit KN8 Ultra
   - ASUS A8Jm (laptop)
   - ASUS A8N (might need changing to "A8N-SLI Deluxe", see
     http://www.coreboot.org/pipermail/flashrom/2009-November/000878.html)
   - ASUS A8N-LA (Nagami-GL8E)
   - ASUS P4B533-E
   - ASUS P4S800-MX
   - HP ProLiant DL165 G6
   - IBASE MB899
   - Intel SE440BX-2 (marked as non-working for now though, due to
     http://www.coreboot.org/pipermail/flashrom/2010-July/003952.html

)
   - MSI MS-6577 (Xenon)
   - MSI MS-7207 (K8NGM2-L)

- Fix / amend a few board names:

   - Add "ProLiant" name to the "DL145 G3" (and the new "DL165 G6"), we
     use such "series" names for various other boards (e.g. "Vectra" etc)
     and it also helps users googling for those names.

   - HP "Vectra VL400 PC" should be "Vectra VL400" really, I'm pretty sure
     the "PC" is not part of the board name but simply stands for
     "personal computer". Same for "Vectra VL420 SFF PC".

   - Change "ASUS A8JM" to "ASUS A8Jm" as per vendor website.

   - Add comments for boards which may be listed with incorrect names,
     I sent out clarification requests to the list, URLs listed as comment.

   - Add "Xenon" HP name to the "MSI MS-6577" OEM board.

   - Fix typo in "MS-7207 (K8N GM2-L)", should be "MS-7207 (K8NGM2-L)" as
     per vendor website.

Corresponding to flashrom svn r1141.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Change the DMI string to only match this exact board (DMI "NAGAMI2L")
as only this one is tested.

Similar HP OEM boards might also work using this board-enable but that's
not sure and not tested. Two of those boards have DMI strings "NAGAMI"
and "NAGAMI2".

Corresponding to flashrom svn r1140.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

lspci/superiotool:
  http://www.coreboot.org/pipermail/flashrom/2010-August/004414.html



(URL added by Michael Karcher)

Corresponding to flashrom svn r1139.
Signed-off-by: Mattias Mattsson <vitplister@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

I had to use the USB controller in the board enable because all other
subsystem IDs are having vendor: Gigabyte but mostly copy the Intel
product IDs.

lspci/superiotool:
  http://www.coreboot.org/pipermail/flashrom/2010-August/004420.html



Corresponding to flashrom svn r1138.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Thomas Kalka <thomas.kalka@googlemail.com>

 - Fix incorrect whitespace, indentation, and coding style in some places.

 - Drop '/**' Doxygen comments, we don't use Doxygen. Even if we would use
   it, the comments are useless as we don't have any Doxygen markup in there.

 - Use consistent vendor name spelling as per current website (NVIDIA,
   abit, GIGABYTE).

 - Use consistent / common format for "Suited for:" lines in board_enable.c.

 - Add some missing 'void's in functions taking no arguments.

 - Add missing fullstops in sentences, remove them from non-sentences (lists).

Corresponding to flashrom svn r1134.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

This was successfully tested by 'kai2343' on IRC.

Thanks to Michael Karcher for finding the board enable.

Corresponding to flashrom svn r1133.
Signed-off-by: Joshua Roys <roysjosh@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Boards:

 - ASUS M4A785TD-M EVO (reported by Mattias Mattsson <vitplister@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-August/004283.html

 - ASUS M2N32-SLI Deluxe (reported by Mattias Mattsson <vitplister@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-August/004287.html

 - ASUS P2E-M (reported by Mattias Mattsson <vitplister@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-July/004261.html

 - ASUS M2N-SLI Deluxe (reported by
   Kasper M. Nielsen <kasper.nielsen85@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-May/003015.html
   
 - iBASE MB899 (reported by Bernhard M. Wiedemann <bernhard@lsmod.de>)
   http://www.flashrom.org/pipermail/flashrom/2010-April/002953.html
   
   Board-enable is now marked as tested.

 - ASRock 939A785GMH/128M (reported by
   Lennart Sauerbeck <lists@lennart.sauerbeck.org>)
   http://www.flashrom.org/pipermail/flashrom/2010-August/004340.html

Corresponding to flashrom svn r1132.

Chips:
 
 - ST M50FLW080A (reported by Mattias Mattsson <vitplister@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-August/004287.html
 
 - Winbond W29EE011 (reported by Mattias Mattsson <vitplister@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-July/004261.html
 
 - SST SST49LF040 (reported by Mattias Mattsson <vitplister@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-August/004296.html

Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Thanks to "Putlinuxonit" <putlinuxonit@gmail.com> for reporting
and testing.
lspci/superiotool:
  http://www.coreboot.org/pipermail/flashrom/2010-August/004309.html



Corresponding to flashrom svn r1131.
Signed-off-by: Joshua Roys <roysjosh@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

lspci/superiotool:
  http://www.coreboot.org/pipermail/flashrom/2010-July/004172.html



Corresponding to flashrom svn r1130.
Signed-off-by: David Borg <borg.db@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Mark the following boards as supported:

 - Foxconn A6VMX (reported by Alec Wright <alecjw@member.fsf.org>)
   http://www.flashrom.org/pipermail/flashrom/2010-July/004186.html

 - GIGABYTE GA-8IRML (reported by Putlinuxonit <putlinuxonit@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-July/004175.html

   Marking the board-enable as tested now.

 - MSI MS-7253 (K9VGM-V) (reported by Alex <cerebro.alexiel@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-June/003411.html

 - Soyo SY-6BA+ III (reported by Andrew Morgan <ziltro@ziltro.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-June/003409.html

 - GIGABYTE GA-770TA-UD3 (reported by Hering <boerni@pakke.de>)
   http://www.flashrom.org/pipermail/flashrom/2010-May/003267.html

 - Shuttle AV11V30 (reported by
   "Néstor a.k.a. DarkMan" <master_darkman@hotmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-May/003260.html

 - Tyan S3992 (reported by Alessandro Gervaso <gervaso@appliedgenomics.org>)
   http://www.flashrom.org/pipermail/flashrom/2010-May/003129.html

 - GIGABYTE GA-MA785GMT-UD2H (reported by
   Dominick Layfield <dom.layfield@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-May/003061.html

Mark the following chips as tested:

 - ST M25P10-A (reported by Joshua Blanton <jblanton@rldrake.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-June/003451.html

 - ST M50FLW080A (reported by Vincent Pelletier <plr.vincent@gmail.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-June/003410.html

   Marked PROBE and READ as tested.

 - SST SST39SF020A (reported by Andrew Morgan <ziltro@ziltro.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-June/003409.html

 - AMD Am29F010A/B (reported by Andrew Morgan <ziltro@ziltro.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-June/003335.html

 - SST SST39VF010 (reported by Tim Small <tim@buttersideup.com>)
   http://www.flashrom.org/pipermail/flashrom/2010-May/003310.html



Corresponding to flashrom svn r1129.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Programmer specific functions are of absolutely no interest to any file
except those dealing with programmer specific actions (special SPI
commands and the generic core).

The new header structure is as follows (and yes, improvements are
possible):
flashchips.h  flash chip IDs
chipdrivers.h  chip-specific read/write/... functions
flash.h  common header for all stuff that doesn't fit elsewhere
hwaccess.h hardware access functions
programmer.h  programmer specific functions
coreboot_tables.h  header from coreboot, internal programmer only
spi.h SPI command definitions

Corresponding to flashrom svn r1112.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

To be safe, the onboard video of the nView edition of this board has
been included in the match. If other NF-M2 editions have the same board
enable, the match should be broadened

lspci/superiotool
  http://www.coreboot.org/pipermail/flashrom/2010-April/002909.html



No success report, thus committed as untested.

Corresponding to flashrom svn r1109.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

The SATA controller matched in the board enable is not always present
with that ID (that's the 2-port ICH9 SATA IDE controller), but (depending
on board revision/edition or BIOS settings an ICH9 SATA RAID controller
appears instead. This patches matches on the SMBus function in the
south bridge instead of the SATA controller.

Non-working board reported by: Gunter Keilholz <gunter.keilholz@googlemail.com>
lspci/superiotool:
  http://www.coreboot.org/pipermail/flashrom/2010-June/003591.html



Corresponding to flashrom svn r1108.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

lspci/superiotool:
http://www.coreboot.org/pipermail/flashrom/2010-July/003889.html



Corresponding to flashrom svn r1107.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Tested-by: Alex Loktionoff <oxy-loktionoff@mail.ru>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Non-working board reported by idlogin / Putlinuxonit <putlinuxonit@gmail.com>
lspci/superiotool:
  http://www.coreboot.org/pipermail/flashrom/2010-May/003330.html


No success report, so committed as untested.

Corresponding to flashrom svn r1106.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Non-working board reported by: Anders Jenbo <anders@jenbo.dk>
lspci/superiotool:
  http://www.coreboot.org/pipermail/flashrom/2010-June/003346.html



no success report, so committed as untested.

Corresponding to flashrom svn r1105.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r1103.
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

lspci/superiotool:
  http://www.coreboot.org/pipermail/flashrom/2010-July/003869.html



Corresponding to flashrom svn r1102.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Mattias Mattsson <vitplister@gmail.com>

No response from reporter - committed as "untested".

Corresponding to flashrom svn r1101.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r1100.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Tested-by: František Kučera <linux@frantovo.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Needed on the original Xbox running Xebian and a few other ancient
systems.

Corresponding to flashrom svn r1088.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Alec Wright <alecjw@member.fsf.org>

Autodetect the ITE IT8705 Super I/O and enable flash writes if it
performs LPC->Parallel translation. Remove board enables which triggered
the IT8705 write enable manually. Change the IT87 SPI special case to
cover IT87 LPC->SPI and LPC->Parallel translation.

Corresponding to flashrom svn r1073.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Tested on Syntax SV266A.
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>

Tested on Shuttle AK38N, all operations work fine.
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

r1063 had several issues: The PCI IDs for this board are copy/pasted from
the A8N and plain wrong for this board and the board enable is marked as
tested although it isn't. Finally the board description was slightly
wrong and the URL missing.

Corresponding to flashrom svn r1071.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Constify variables where possible.
Initialize programmer-related variables explicitly in programmer_init to
allow running programmer_init from a clean state after
programmer_shutdown.
Prohibit registering programmer shutdown functions before init or after
shutdown.
Kill some dead code.
Rename global variables with namespace-polluting names.
Use a previously unused locking helper function in sst49lfxxxc.c.

This is needed for libflashrom.

Effects on the binary size of flashrom are minimal (300 bytes
shrinkage), but the data section shrinks by 4384 bytes, and that's a
good thing if flashrom is operating in constrained envionments.

Corresponding to flashrom svn r1068.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Change the match for the HP DL145 G3 to avoid matching on the DL165 G6.

Corresponding to flashrom svn r1065.
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numascale.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r1064.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r1063.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Sean Nelson <audiohacked@gmail.com>

This patch unifies the code for different Winbond W83627-family chips,
to be applied before I add another W83627 GPIO raise function.

After the Ack I added the check for unimplemented GPIO ports, but still
dared to reuse the ack.

Corresponding to flashrom svn r1062.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Sean Nelson <audiohacked@gmail.com>

Fix compiler error (bad forward port in r1040).

Corresponding to flashrom svn r1042.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Test report is
http://www.coreboot.org/pipermail/flashrom/2010-April/002967.html



Corresponding to flashrom svn r1041.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Tested-by: Valentine "Pegasus rider" Yatsenko <mr.qweo@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Reporter/owner of that board: oscar <oshikore@gmail.com>
http://www.coreboot.org/pipermail/flashrom/2010-April/002910.html



Corresponding to flashrom svn r1040.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Every board-enable function is passed a 'const char *name' (board name)
which is totally useless as the board name was already printed by flashrom
at that point. Also, 95% or so of the board-enables don't use the
parameter anyway. So, drop it.

Corresponding to flashrom svn r1037.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Also modifies nvidia_mcp_gpio_set to cope with multiple MCP55 chips on
the same board, like on the Tyan S2915-E.

Corresponding to flashrom svn r1025.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Adis Salcin <crow@linux.org.ba>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Unistd.h was only used to get a definition of NULL in all files. Add our
own NULL #define and remove unistd.h from flash.h
stdio.h has no place in flash.h, it should be included only in files
which really need it.
Add #include statements in individual .c files where needed.

Replace a few printf with msg_* to eliminate the need for stdio.h.

Corresponding to flashrom svn r1021.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

At least it's addressed as 'Pro' in the list of boards, which requires
board_enable.

See also:
http://www.flashrom.org/pipermail/flashrom/2009-July/000003.html



Corresponding to flashrom svn r1015.
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Corresponding to flashrom svn r1014.
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>