GitLab

Change the nicnatsemi address mask to use MA0-MA16 and set the maximum
decode size to 128KB.

Corresponding to flashrom svn r1095.
Signed-off-by: Andrew Morgan <ziltro@ziltro.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r1094.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

To use the RayeR driver, run
flashrom -p rayer_spi -V

Known bugs/limitations:
- Won't compile/work on non-x86 architectures.
- Will always use direct port I/O access.

Log follows:

flashrom v0.9.2-r1039 on MS-DOS 7 (i686), built with libpci 3.1.5, GCC 
4.3.2, little endian
Calibrating delay loop... OK.
Initializing rayer_bitbang_spi programmer
Using port 0x378 as I/O base for parallel port access.
...
Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 
0xc2, id2 0x2015
...
Found chip "Macronix MX25L1605" (2048 KB, SPI) at physical address 
0xffe00000.
...
No operations were specified.

Corresponding to flashrom svn r1093.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Martin Rehak <rayer@seznam.cz>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Corresponding to flashrom svn r1092.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Corresponding to flashrom svn r1091.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Fix a bug where 4 GB of spaces would be printed per line if a vendor
name was longer than 10 chars.

This patch is needed to commit MoselVitelic chip support.

Corresponding to flashrom svn r1090.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Use the BAR value returned by pcidev_init which automatically applies
the correct BAR mask for the drkaiser driver. Truncate flash chip
addresses to fit into the 128 kB memory window for drkaiser and pick the
same window size for gfxnvidia.

Uwe tested all operations successfully on a Dr. Kaiser card.

Corresponding to flashrom svn r1089.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Needed on the original Xbox running Xebian and a few other ancient
systems.

Corresponding to flashrom svn r1088.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Alec Wright <alecjw@member.fsf.org>

Newer llvm/clang versions (since r102686) have a __clang_version__ macro
which can be used to print the exact clang version.

Fix a case where chip_to_probe was referenced twice via extern, once at
the function level and once in a global include file. Found by latest
clang.

Corresponding to flashrom svn r1087.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

This chip is used on some Xbox versions.

Corresponding to flashrom svn r1086.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Alec Wright <alecjw@member.fsf.org>

Change the SPI bitbanging core to fix a subtle bug (which had no
effect so far) and to make integration of the RayeR SPIPGM and Nvidia
MCP6x/MCP7x SPI patches easier. Kill a few global variables and require
explicit initialization of bitbanging delay.

A big to Johannes Sjölund for testing an earlier version of the code as
part of the Nvidia MCP6x/MCP7x SPI bitbanging patch.

Corresponding to flashrom svn r1085.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

This removes the need of allocating an extra buffer, but also removes
the possibility of having the data read back during the initial write
phase for debugging purposes.

Compile tested, no functional testing.

Corresponding to flashrom svn r1084.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Use full-chip write function on Fujitsu MBM29F400TC and ST M29F400BT.
Add support for ST M29F400BB.

Corresponding to flashrom svn r1083.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Actually check if the unlock worked instead of just assuming it worked.

Corresponding to flashrom svn r1082.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Use this instead of the open-coding variant that only aborts after it is too late.

Corresponding to flashrom svn r1081.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

However, wrap the write functions in a compat layer to allow converting
the rest of flashrom later. Tested on Intel NM10 by David Hendricks.

Corresponding to flashrom svn r1080.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Improve error checking in file write, chip read and chip verify.
Refactor the read routines a bit to split reading from file writing.

Log for a failed read:
[...]
Found chip "Winbond W25x16" (2048 KB, SPI) at physical address
0xffe00000.
Reading flash... Invalid OPCODE 0x03
Read operation failed!
FAILED.

Corresponding to flashrom svn r1079.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stephen Kou <stephen@hyarros.com>

Corresponding to flashrom svn r1078.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

That allows us to use erase region walking for a combined erase/write
action, and is a prerequisite for partial flashing,

Corresponding to flashrom svn r1077.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

A bit was masked, but not shifted, and that led to worst-case accesses
of index 24 in an array with 4 members.

I've improved readability in the variable declaration block as well.

Thanks to Stephen Kou for reporting the bug.

Corresponding to flashrom svn r1076.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stephen Kou <stephen@hyarros.com>

This is a 1 MB SPI chip that seems to be straightforwardly related
to the AMIC A25L40PU, which has half the capacity but is otherwise
identical.

Datasheet is at http://www.amictechnology.com/pdf/A25L80P.pdf



flashrom -VE, -Vr, and -Vw has been tested using the AMD SB7x0
interface. Everything works fine... at least, I used it to upgrade my
BIOS and I've been able to reboot.

Corresponding to flashrom svn r1075.
Signed-off-by: Daniel Lenski <dlenski@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

SPI chips never should use read_memmapped. The SPI master code might
decide that read_memmapped is fine for this chip, though, in a lower
layer.

Corresponding to flashrom svn r1074.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Autodetect the ITE IT8705 Super I/O and enable flash writes if it
performs LPC->Parallel translation. Remove board enables which triggered
the IT8705 write enable manually. Change the IT87 SPI special case to
cover IT87 LPC->SPI and LPC->Parallel translation.

Corresponding to flashrom svn r1073.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Tested on Syntax SV266A.
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>

Tested on Shuttle AK38N, all operations work fine.
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Make programmer_param static by converting all users to extract_programmer_param.
Programmer parameters can no longer be separated with a
colon, they have to be separated with a comma.

Corresponding to flashrom svn r1072.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

r1063 had several issues: The PCI IDs for this board are copy/pasted from
the A8N and plain wrong for this board and the board enable is marked as
tested although it isn't. Finally the board description was slightly
wrong and the URL missing.

Corresponding to flashrom svn r1071.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

This led to wildly differing syntax for programmer parameters, and
it also voids pretty much every assumption you could make about
programmer_param. The latter is a problem for libflashrom.

Use extract_param everywhere, clean up related code and make it more
foolproof. Add two instances of exit(1) where we have no option to
return an error. Remove six instances of exit(1) where returning an
error was possible.

WARNING: This changes programmer parameter syntax for a few programmers!

Corresponding to flashrom svn r1070.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

If a programmer has untested or non-working write/erase code, but
probing/reading works, it makes sense to protect the user against
write/erase accidents. This feature will be used by the Nvidia MCP SPI
code, and it also might make sense for the gfxnvidia driver which has
non-working write/erase.

Corresponding to flashrom svn r1069.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Constify variables where possible.
Initialize programmer-related variables explicitly in programmer_init to
allow running programmer_init from a clean state after
programmer_shutdown.
Prohibit registering programmer shutdown functions before init or after
shutdown.
Kill some dead code.
Rename global variables with namespace-polluting names.
Use a previously unused locking helper function in sst49lfxxxc.c.

This is needed for libflashrom.

Effects on the binary size of flashrom are minimal (300 bytes
shrinkage), but the data section shrinks by 4384 bytes, and that's a
good thing if flashrom is operating in constrained envionments.

Corresponding to flashrom svn r1068.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>

Add a requirements section to the man page which lists the needed access
permissions for each programmer.

This feature needs my pciutils/libpci 8/16-bit write emulation patch at
http://marc.info/?l=openbsd-ports&m=127780030728045

 titled
[PATCH] Fix pciutils non-32bit PCI write on OpenBSD

Corresponding to flashrom svn r1067.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stuart Henderson <sthen@openbsd.org>

Corresponding to flashrom svn r1066.
Signed-off-by: Joshua Roys <roysjosh@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Change the match for the HP DL145 G3 to avoid matching on the DL165 G6.

Corresponding to flashrom svn r1065.
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numascale.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r1064.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r1063.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Sean Nelson <audiohacked@gmail.com>

This patch unifies the code for different Winbond W83627-family chips,
to be applied before I add another W83627 GPIO raise function.

After the Ack I added the check for unimplemented GPIO ports, but still
dared to reuse the ack.

Corresponding to flashrom svn r1062.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Sean Nelson <audiohacked@gmail.com>

This is needed for warning-free compilation on older gcc versions (3.x
and probably older). Such a gcc version is the default on i386 OpenBSD.

Corresponding to flashrom svn r1061.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stuart Henderson <sthen@openbsd.org>

Corresponding to flashrom svn r1060.
Signed-off-by: Guenter Knauf <lists@gknw.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Tested.

Corresponding to flashrom svn r1059.
Signed-off-by: David Hendricks <dhendrix@google.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Provide empty DMI stubs for that case until someone implements our own
dmidecode subset.

Tested by Patrick Georgi on top of libpayload.

Corresponding to flashrom svn r1058.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>

Tested on Linux, FreeBSD, NetBSD, OpenBSD, DOS.
Thanks to Jonathan A. Kollasch and Idwer Vollering for testing.

Corresponding to flashrom svn r1057.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Idwer Vollering <vidwer+lists.flashrom@gmail.com>

Corresponding to flashrom svn r1056.
Signed-off-by: David Borg <borg.db@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>