GitLab

Some vendors like Programmable Micro Corp (PMC) need this. Both the
serial and parallel flash JEDEC detection routines would benefit from a
parity/sanity check of the vendor ID. Will do this later.

Add support for the PMC Pm25LV family of SPI flash chips.

Corresponding to flashrom svn r191 and coreboot v2 svn r3091.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Chris Lingard  <chris@stockwith.co.uk>

Make the vendor name optional in the -m flashrom parameter when there's only one board name that matches

The full syntax still works, and is required when two vendors have
boards with the same names.

Corresponding to flashrom svn r190 and coreboot v2 svn r3082.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

Corresponding to flashrom svn r189 and coreboot v2 svn r3080.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>

Corresponding to flashrom svn r188 and coreboot v2 svn r3078.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Peter Stuge <peter@stuge.se>

Tested on the pcengines alix1c and works fine.
Acked-by: Ronald G. Minnich <rminnich@gmail.com>

Corresponding to flashrom svn r187 and coreboot v2 svn r3074.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

I've tested and verified the chip myself, and it seems to work
everything like supposted, since Carl-Daniel has patched flashrom to
use the read funktion on verifying. 

"benchvice flashrom # ./flashrom -m gigabyte:m57sli -v test.4mb
Calibrating delay loop... OK.
No coreboot table found.
Found chipset "NVIDIA MCP55", enabling flash write... OK.
Found board "GIGABYTE GA-M57SLI-S4": enabling flash write... 
Serial flash segment 0xfffe0000-0xffffffff enabled
Serial flash segment 0x000e0000-0x000fffff enabled
Serial flash segment 0xffee0000-0xffefffff disabled
Serial flash segment 0xfff80000-0xfffeffff enabled
LPC write to serial flash enabled
serial flash pin 29
OK.
MX25L3205 found at physical address 0xffc00000.
Flash part is MX25L3205 (4096 KB).
Flash image seems to be a legacy BIOS. Disabling checks.
Verifying flash... VERIFIED.
benchvice flashrom # ls -l test.4mb
-rw-r--r-- 1 root root 4194304 22. Jan 16:27 test.4mb

Corresponding to flashrom svn r186 and coreboot v2 svn r3072.
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

That fails if the flash chip is not mapped completely. If the read
function is set in struct flashchip, use it for verification as well.

This fixes verification of all SPI flash chips >512 kByte behind an
IT8716F flash translation chip.

"MX25L8005 found at physical address 0xfff00000. Flash part is MX25L8005
(1024 KB). Flash image seems to be a legacy BIOS. Disabling checks.
Verifying flash... VERIFIED."

Corresponding to flashrom svn r185 and coreboot v2 svn r3070.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Harald Gutmann <harald.gutmann@gmx.net>

Minor formatting changes.

Corresponding to flashrom svn r184 and coreboot v2 svn r3069.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Harald Gutmann <harald.gutmann@gmx.net>

readcnt==0 saves 10 seconds with the unconditional 10us delay, reducing
programming time for SST25VF016B to 40-45 secs.

Corresponding to flashrom svn r183 and coreboot v2 svn r3068.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Because 'v' and 'V' are already in use, the patch uses 'R' (for release)
and, of course, '--version'.

Corresponding to flashrom svn r182 and coreboot v2 svn r3067.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Acked-by: Ulf Jordan <jordan@chalmers.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Support SPI flash chips bigger than 512 kByte sitting behind IT8716F
Super I/O performing LPC-to-SPI flash translation.

Corresponding to flashrom svn r181 and coreboot v2 svn r3061.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r180 and coreboot v2 svn r3059.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Corresponding to flashrom svn r179 and coreboot v2 svn r3058.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

Corresponding to flashrom svn r178 and coreboot v2 svn r3054.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

After the patch [...] The line length is still below 80 characters.

Corresponding to flashrom svn r177 and coreboot v2 svn r3045.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Acked-by: Torsten Duwe <duwe@lst.de>

The #defines were already there.

Corresponding to flashrom svn r176 and coreboot v2 svn r3042.
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Straight from the data sheet, not tested.

Corresponding to flashrom svn r175 and coreboot v2 svn r3036.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

Corresponding to flashrom svn r174 and coreboot v2 svn r3033.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r173 and coreboot v2 svn r3032.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>

Improve model number printing.

Add EN29F002(A)(N)B support while I'm at it.

Corresponding to flashrom svn r172 and coreboot v2 svn r3031.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Markus Boas <bios@ryven.de>

The continuation ID code does not go further than checking for IDs of
the type 0x7fXX, but does this for vendor and product ID. The current
published JEDEC spec has a list where the largest vendor ID is 7 bytes
long, but all leading bytes are 0x7f. The list will grow in the future,
and using a 64bit variable will not be enough anymore.
Besides that, it seems that the location of the ID byte after the first
continuation ID byte is very vendor specific, so we may have to revisit
that code some time in the future.

(Suggestion for a new encoding:
Use a two-byte data type for the ID, the lower byte contains the only
non-0x7f byte, the upper byte contains the number of 0x7f bytes used as
prefix, which is the bank number minus 1 the vendor ID appears in.)

Add support for EON EN29F002AT.

Corresponding to flashrom svn r171 and coreboot v2 svn r3030.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>

This fixes a few vendor IDs to conform with JEDEC publication 106W
(JEP106W), adds some device IDs and provides information about
non-conforming IDs. The EON change is left to the patch adding EON
chips.

This patch should have no effect on code generation.

Corresponding to flashrom svn r170 and coreboot v2 svn r3029.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>

Fix that. Page size is uniform 256 bytes for SPI.

A sector/block size field in struct flashchip would be nice, though.

Corresponding to flashrom svn r169 and coreboot v2 svn r3027.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>

Pretty-print the chip status register (including block lock information)
for ST M25P family and Macronix MX25L family chips.

Corresponding to flashrom svn r168 and coreboot v2 svn r3026.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>

Untested, but verified against the data sheet.

Corresponding to flashrom svn r167 and coreboot v2 svn r3025.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>

Add support for ST M25P05-A, M25P10-A, M25P20, M25P40, M25P16, M25P32,
M25P64, M25P128.

ST M25P80 support is already there. Not tested, but conforming to data
sheets and double checked.

Corresponding to flashrom svn r166 and coreboot v2 svn r3012.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

To make it easier to add new SPI chips to flashchips.c, rename functions
with multiple possible opcodes from linear numbering at the end (_1, _2)
to include the opcode at the end (_60, _c7).

That way, you only have to take a short look at the data sheet and
choose the right function by appending the opcode listed in the data
sheet. No functional changes.

Corresponding to flashrom svn r165 and coreboot v2 svn r3009.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>

Detection was tested. Print status register before erase to help
debugging block locks.

Corresponding to flashrom svn r164 and coreboot v2 svn r3008.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>

AT49F002
AT49F002N
AT49F002T
AT49F002NT

Only tested the read function on AT49F002T.
datasheet @ http://www.atmel.com/atmel/acrobat/doc1017.pdf



Corresponding to flashrom svn r163 and coreboot v2 svn r3003.
Signed-off-by: Frederico Silva <frederico.silva@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Also, s/0xFF80/0xFFC0/ in the Acorp 6A815EPD board-enable, as per
http://www.linuxbios.org/pipermail/linuxbios/2007-December/027750.html



Corresponding to flashrom svn r162 and coreboot v2 svn r2997.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Corresponding to flashrom svn r161 and coreboot v2 svn r2995.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

Attached is a patch that enables AMD Geode CS5536 chipset support.  I
have tested it successfully on a MSM800 board from digital logic.

Corresponding to flashrom svn r160 and coreboot v2 svn r2967.
Signed-off-by: Lane Brooks <lbrooks@mit.edu>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>

The JEDEC probe routine had a delay of 10 us after entering ID mode
and this was insufficient for the 29C020. The data sheet claims we
have to wait 10 ms, but tests have shown that 20 us suffice. Allow for
variations in chip delays with a factor of 2 safety margin.

Corresponding to flashrom svn r159 and coreboot v2 svn r2962.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>

Detection and reading works, writing is not tested.

Corresponding to flashrom svn r158 and coreboot v2 svn r2903.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>

Looking through the sources of Uniflash utility I found that this chip
is no more no less than low-voltage variant of Am29F040B but with
different ID.

So I created a very quick patch (attached).

Corresponding to flashrom svn r157 and coreboot v2 svn r2897.
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>

Corresponding to flashrom svn r156 and coreboot v2 svn r2884.
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Corresponding to flashrom svn r155 and coreboot v2 svn r2881.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

This has been tested by Harald Gutmann <harald.gutmann@gmx.net> with a
MX25L4005 chip.

Corresponding to flashrom svn r154 and coreboot v2 svn r2876.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>

Corresponding to flashrom svn r153 and coreboot v2 svn r2875.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>

The first chip the code was tested and verified with is the Macronix
MX25L4005, but other chips should work as well. Timeouts are still
hardcoded to data sheet maxima, but the status register checking code is
already there. Thanks to Harald Gutmann for the initial code on which
this is loosely based.

Corresponding to flashrom svn r152 and coreboot v2 svn r2874.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>