Commit 41d6bd91 authored by Carl-Daniel Hailfinger's avatar Carl-Daniel Hailfinger
Browse files

Rewrite the SB600 chipset enable function


- Check for read/write protected regions first.
- Region protection is write-once according to the data sheets. Check if
the write succeeded. Don't write if the region is not protected.
- Verbose region protection dumping.
- Improve readability of BAR mapping code.
- Align BAR mapping to a page boundary (4k) instead of a 16k boundary.

This patch prepares the code for a SPI detection heuristic.

Corresponding to flashrom svn r463.
Signed-off-by: default avatarCarl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: default avatarPeter Stuge <peter@stuge.se>
parent b452a913
......@@ -658,33 +658,49 @@ static int enable_flash_amd8111(struct pci_dev *dev, const char *name)
static int enable_flash_sb600(struct pci_dev *dev, const char *name)
{
uint32_t tmp, low_bits, num;
uint32_t tmp, prot;
uint8_t reg;
low_bits = tmp = pci_read_long(dev, 0xa0);
low_bits &= ~0xffffc000; /* for mmap aligning requirements */
low_bits &= 0xfffffff0; /* remove low 4 bits */
tmp &= 0xffffc000;
printf_debug("SPI base address is at 0x%x\n", tmp + low_bits);
sb600_spibar = physmap("SB600 SPI registers", tmp, 0x4000);
sb600_spibar += low_bits;
/* Clear ROM protect 0-3. */
for (reg = 0x50; reg < 0x60; reg += 4) {
num = pci_read_long(dev, reg);
num &= 0xfffffffc;
pci_write_byte(dev, reg, num);
prot = pci_read_long(dev, reg);
/* No protection flags for this region?*/
if ((prot & 0x3) == 0)
continue;
printf_debug("SB600 %s%sprotected from %u to %u\n",
(prot & 0x1) ? "write " : "",
(prot & 0x2) ? "read " : "",
(prot & 0xfffffc00),
(prot & 0xfffffc00) + ((prot & 0x3ff) << 8));
prot &= 0xfffffffc;
pci_write_byte(dev, reg, prot);
prot = pci_read_long(dev, reg);
if (prot & 0x3)
printf("SB600 still %s%sprotected from %u to %u\n",
(prot & 0x1) ? "write " : "",
(prot & 0x2) ? "read " : "",
(prot & 0xfffffc00),
(prot & 0xfffffc00) + ((prot & 0x3ff) << 8));
}
/* Read SPI_BaseAddr */
tmp = pci_read_long(dev, 0xa0);
tmp &= 0xfffffff0; /* remove low 4 bits (reserved) */
printf_debug("SPI base address is at 0x%x\n", tmp);
/* Physical memory can only be mapped at page (4k) boundaries */
sb600_spibar = physmap("SB600 SPI registers", tmp & 0xfffff000, 0x1000);
/* The low bits of the SPI base address are used as offset into the mapped page */
sb600_spibar += tmp & 0xfff;
flashbus = BUS_TYPE_SB600_SPI;
/* Enable SPI ROM in SB600 PM register. */
/* If we enable SPI ROM here, we have to disable it after we leave.
/* Force enable SPI ROM in SB600 PM register.
* If we enable SPI ROM here, we have to disable it after we leave.
* But how can we know which ROM we are going to handle? So we have
* to trade off. We only access LPC ROM if we boot via LPC ROM. And
* only SPI ROM if we boot via SPI ROM. If you want to do it crossly,
* you have to use the code below.
* only SPI ROM if we boot via SPI ROM. If you want to access SPI on
* boards with LPC straps, you have to use the code below.
*/
/*
OUTB(0x8f, 0xcd6);
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment