diff --git a/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt
new file mode 100644
index 0000000000000000000000000000000000000000..02649d8b3f5a372500fedfff7db12ae496a9dfba
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt
@@ -0,0 +1,35 @@
+Mediatek MT6311 Regulator Driver
+
+Required properties:
+- compatible: "mediatek,mt6311-regulator"
+- reg: I2C slave address, usually 0x6b.
+- regulators: List of regulators provided by this controller. It is named
+ to VDVFS and VBIASN.
+ The definition for each of these nodes is defined using the standard binding
+ for regulators at Documentation/devicetree/bindings/regulator/regulator.txt.
+
+The valid names for regulators are:
+BUCK:
+ VDVFS
+LDO:
+ VBIASN
+
+Example:
+ mt6311: pmic@6b {
+ compatible = "mediatek,mt6311-regulator";
+ reg = <0x6b>;
+
+ regulators {
+ mt6311_vcpu_reg: VDVFS {
+ regulator-name = "VDVFS";
+ regulator-min-microvolt = < 600000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-ramp-delay = <10000>;
+ };
+ mt6311_ldo_reg: VBIASN {
+ regulator-name = "VBIASN";
+ regulator-min-microvolt = <200000>;
+ regulator-max-microvolt = <800000>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
index ce91f61feb12554e0d62d84ebe93d13e9e6fbf59..ed936f0f34f28446e5151e238b7bf31161658b0c 100644
--- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
@@ -1,27 +1,68 @@
-pwm regulator bindings
+Bindings for the Generic PWM Regulator
+======================================
+
+Currently supports 2 modes of operation:
+
+Voltage Table: When in this mode, a voltage table (See below) of
+ predefined voltage <=> duty-cycle values must be
+ provided via DT. Limitations are that the regulator can
+ only operate at the voltages supplied in the table.
+ Intermediary duty-cycle values which would normally
+ allow finer grained voltage selection are ignored and
+ rendered useless. Although more control is given to
+ the user if the assumptions made in continuous-voltage
+ mode do not reign true.
+
+Continuous Voltage: This mode uses the regulator's maximum and minimum
+ supplied voltages specified in the
+ regulator-{min,max}-microvolt properties to calculate
+ appropriate duty-cycle values. This allows for a much
+ more fine grained solution when compared with
+ voltage-table mode above. This solution does make an
+ assumption that a %50 duty-cycle value will cause the
+ regulator voltage to run at half way between the
+ supplied max_uV and min_uV values.
Required properties:
-- compatible: Should be "pwm-regulator"
-- pwms: OF device-tree PWM specification (see PWM binding pwm.txt)
-- voltage-table: voltage and duty table, include 2 members in each set of
- brackets, first one is voltage(unit: uv), the next is duty(unit: percent)
+--------------------
+- compatible: Should be "pwm-regulator"
+
+- pwms: PWM specification (See: ../pwm/pwm.txt)
+
+Only required for Voltage Table Mode:
+- voltage-table: Voltage and Duty-Cycle table consisting of 2 cells
+ First cell is voltage in microvolts (uV)
+ Second cell is duty-cycle in percent (%)
+
+NB: To be clear, if voltage-table is provided, then the device will be used
+in Voltage Table Mode. If no voltage-table is provided, then the device will
+be used in Continuous Voltage Mode.
-Any property defined as part of the core regulator binding defined in
-regulator.txt can also be used.
+Any property defined as part of the core regulator binding can also be used.
+(See: ../regulator/regulator.txt)
-Example:
+Continuous Voltage Example:
pwm_regulator {
compatible = "pwm-regulator;
pwms = <&pwm1 0 8448 0>;
+ regulator-min-microvolt = <1016000>;
+ regulator-max-microvolt = <1114000>;
+ regulator-name = "vdd_logic";
+ };
+Voltage Table Example:
+ pwm_regulator {
+ compatible = "pwm-regulator;
+ pwms = <&pwm1 0 8448 0>;
+ regulator-min-microvolt = <1016000>;
+ regulator-max-microvolt = <1114000>;
+ regulator-name = "vdd_logic";
+
+ /* Voltage Duty-Cycle */
voltage-table = <1114000 0>,
<1095000 10>,
<1076000 20>,
<1056000 30>,
<1036000 40>,
<1016000 50>;
-
- regulator-min-microvolt = <1016000>;
- regulator-max-microvolt = <1114000>;
- regulator-name = "vdd_logic";
};
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index db88feb28c0313bc9914eb2bcb4fc33dde264295..24bd422cecd5857c7fcf07403f5b600fd6310f3c 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -42,6 +42,7 @@ Optional properties:
- regulator-system-load: Load in uA present on regulator that is not captured by
any consumer request.
- regulator-pull-down: Enable pull down resistor when the regulator is disabled.
+- regulator-over-current-protection: Enable over current protection.
Deprecated properties:
- regulator-compatible: If a regulator chip contains multiple
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index a7b81f0185b56c6c7a428bc32eebda3612c4600c..f3cdf7a4e4871dddade312b95456ec3814579d93 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -443,6 +443,15 @@ config REGULATOR_MC13892
Say y here to support the regulators found on the Freescale MC13892
PMIC.
+config REGULATOR_MT6311
+ tristate "MediaTek MT6311 PMIC"
+ depends on I2C
+ help
+ Say y here to select this option to enable the power regulator of
+ MediaTek MT6311 PMIC.
+ This driver supports the control of different power rails of device
+ through regulator interface.
+
config REGULATOR_MT6397
tristate "MediaTek MT6397 PMIC"
depends on MFD_MT6397
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 6429e629dcb60c73c5f6505614cf3978abc3b957..8bc702910320532df667f98acc33de146f4ff57b 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -59,6 +59,7 @@ obj-$(CONFIG_REGULATOR_MAX77802) += max77802.o
obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
+obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
diff --git a/drivers/regulator/act8865-regulator.c b/drivers/regulator/act8865-regulator.c
index 2ff73d72ca34aca4d332fa1c7967d35f24471de0..896db168e4bdba4ffd8e75375f42339506cfc0fc 100644
--- a/drivers/regulator/act8865-regulator.c
+++ b/drivers/regulator/act8865-regulator.c
@@ -530,7 +530,6 @@ MODULE_DEVICE_TABLE(i2c, act8865_ids);
static struct i2c_driver act8865_pmic_driver = {
.driver = {
.name = "act8865",
- .owner = THIS_MODULE,
},
.probe = act8865_pmic_probe,
.id_table = act8865_ids,
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 4315476540c4883cf27f960521578efbc9118137..de9f272a0faf75d7562665aebba60444338f21c5 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -1091,6 +1091,15 @@ static int set_machine_constraints(struct regulator_dev *rdev,
}
}
+ if (rdev->constraints->over_current_protection
+ && ops->set_over_current_protection) {
+ ret = ops->set_over_current_protection(rdev);
+ if (ret < 0) {
+ rdev_err(rdev, "failed to set over current protection\n");
+ goto out;
+ }
+ }
+
print_constraints(rdev);
return 0;
out:
diff --git a/drivers/regulator/da9210-regulator.c b/drivers/regulator/da9210-regulator.c
index 8e39f7457bc36a0714aad690f65bcd09e903cf89..b3517830edb6f0ea2139cbc5ebe902ce8cf8265d 100644
--- a/drivers/regulator/da9210-regulator.c
+++ b/drivers/regulator/da9210-regulator.c
@@ -259,7 +259,6 @@ MODULE_DEVICE_TABLE(i2c, da9210_i2c_id);
static struct i2c_driver da9210_regulator_driver = {
.driver = {
.name = "da9210",
- .owner = THIS_MODULE,
},
.probe = da9210_i2c_probe,
.id_table = da9210_i2c_id,
diff --git a/drivers/regulator/da9211-regulator.c b/drivers/regulator/da9211-regulator.c
index 0858100d2d03326335a83d1597632575cd410dc2..04ef65b7eb3d2e225e784f7f3fc166b12ecba522 100644
--- a/drivers/regulator/da9211-regulator.c
+++ b/drivers/regulator/da9211-regulator.c
@@ -512,7 +512,6 @@ MODULE_DEVICE_TABLE(of, da9211_dt_ids);
static struct i2c_driver da9211_regulator_driver = {
.driver = {
.name = "da9211",
- .owner = THIS_MODULE,
.of_match_table = of_match_ptr(da9211_dt_ids),
},
.probe = da9211_i2c_probe,
diff --git a/drivers/regulator/isl6271a-regulator.c b/drivers/regulator/isl6271a-regulator.c
index 6e5da95fa025d4df8c8f3821230ec491be64bd22..4abd8e9c81e5893b4a84d3146db7131c8f42387a 100644
--- a/drivers/regulator/isl6271a-regulator.c
+++ b/drivers/regulator/isl6271a-regulator.c
@@ -156,7 +156,6 @@ MODULE_DEVICE_TABLE(i2c, isl6271a_id);
static struct i2c_driver isl6271a_i2c_driver = {
.driver = {
.name = "isl6271a",
- .owner = THIS_MODULE,
},
.probe = isl6271a_probe,
.id_table = isl6271a_id,
diff --git a/drivers/regulator/isl9305.c b/drivers/regulator/isl9305.c
index e02e9a9dddbdbf47c9b4c60c356a648cc4c334d8..257c1943e7534276a058c9e98f015c26eafeb0ee 100644
--- a/drivers/regulator/isl9305.c
+++ b/drivers/regulator/isl9305.c
@@ -196,7 +196,6 @@ MODULE_DEVICE_TABLE(i2c, isl9305_i2c_id);
static struct i2c_driver isl9305_regulator_driver = {
.driver = {
.name = "isl9305",
- .owner = THIS_MODULE,
.of_match_table = of_match_ptr(isl9305_dt_ids),
},
.probe = isl9305_i2c_probe,
diff --git a/drivers/regulator/lp3971.c b/drivers/regulator/lp3971.c
index 66fd2330dca043a2627c8443f090ba5822f5de14..15c25c622edf69c60adc6ede42401675093b074c 100644
--- a/drivers/regulator/lp3971.c
+++ b/drivers/regulator/lp3971.c
@@ -452,7 +452,6 @@ MODULE_DEVICE_TABLE(i2c, lp3971_i2c_id);
static struct i2c_driver lp3971_i2c_driver = {
.driver = {
.name = "LP3971",
- .owner = THIS_MODULE,
},
.probe = lp3971_i2c_probe,
.id_table = lp3971_i2c_id,
diff --git a/drivers/regulator/lp3972.c b/drivers/regulator/lp3972.c
index aea485afcc1a8a9983781320182ed9078ff9517c..3a7e96e2c7b3c93d9cfc910a080f664145c67ce6 100644
--- a/drivers/regulator/lp3972.c
+++ b/drivers/regulator/lp3972.c
@@ -550,7 +550,6 @@ MODULE_DEVICE_TABLE(i2c, lp3972_i2c_id);
static struct i2c_driver lp3972_i2c_driver = {
.driver = {
.name = "lp3972",
- .owner = THIS_MODULE,
},
.probe = lp3972_i2c_probe,
.id_table = lp3972_i2c_id,
diff --git a/drivers/regulator/lp872x.c b/drivers/regulator/lp872x.c
index 8702e7384af7450d4e7656449f8a1a63603d48b1..e5af07208f9d382ad54fb2e35b358662fff35de8 100644
--- a/drivers/regulator/lp872x.c
+++ b/drivers/regulator/lp872x.c
@@ -961,7 +961,6 @@ MODULE_DEVICE_TABLE(i2c, lp872x_ids);
static struct i2c_driver lp872x_driver = {
.driver = {
.name = "lp872x",
- .owner = THIS_MODULE,
.of_match_table = of_match_ptr(lp872x_dt_ids),
},
.probe = lp872x_probe,
diff --git a/drivers/regulator/ltc3589.c b/drivers/regulator/ltc3589.c
index cc22ac66c8fdb532aa40f3c833a298b261bb17d4..972c386b269024180e512cab2c65da0e069817c6 100644
--- a/drivers/regulator/ltc3589.c
+++ b/drivers/regulator/ltc3589.c
@@ -542,7 +542,6 @@ MODULE_DEVICE_TABLE(i2c, ltc3589_i2c_id);
static struct i2c_driver ltc3589_driver = {
.driver = {
.name = DRIVER_NAME,
- .owner = THIS_MODULE,
},
.probe = ltc3589_probe,
.id_table = ltc3589_i2c_id,
diff --git a/drivers/regulator/max1586.c b/drivers/regulator/max1586.c
index d2a8c64cae42a9bc83890e922b7971781347ee62..2c1228d5796acb1df61cb12c161fc4ba8ed2f1b8 100644
--- a/drivers/regulator/max1586.c
+++ b/drivers/regulator/max1586.c
@@ -304,7 +304,6 @@ static struct i2c_driver max1586_pmic_driver = {
.probe = max1586_pmic_probe,
.driver = {
.name = "max1586",
- .owner = THIS_MODULE,
.of_match_table = of_match_ptr(max1586_of_match),
},
.id_table = max1586_id,
diff --git a/drivers/regulator/max8660.c b/drivers/regulator/max8660.c
index 4071d74fa8288ce27d2cdd34505c006474e2f869..b87f62dd484e0a4ca349e5a9f7d5fbb34aaab349 100644
--- a/drivers/regulator/max8660.c
+++ b/drivers/regulator/max8660.c
@@ -518,7 +518,6 @@ static struct i2c_driver max8660_driver = {
.probe = max8660_probe,
.driver = {
.name = "max8660",
- .owner = THIS_MODULE,
},
.id_table = max8660_id,
};
diff --git a/drivers/regulator/max8973-regulator.c b/drivers/regulator/max8973-regulator.c
index 8857cc02d9a8140ca33703c6f89f49b22578f800..5b75b7c2e3ea441c266a13c367d555b08d46077d 100644
--- a/drivers/regulator/max8973-regulator.c
+++ b/drivers/regulator/max8973-regulator.c
@@ -732,7 +732,6 @@ static struct i2c_driver max8973_i2c_driver = {
.driver = {
.name = "max8973",
.of_match_table = of_max8973_match_tbl,
- .owner = THIS_MODULE,
},
.probe = max8973_probe,
.id_table = max8973_id,
diff --git a/drivers/regulator/mt6311-regulator.c b/drivers/regulator/mt6311-regulator.c
new file mode 100644
index 0000000000000000000000000000000000000000..02c4e5feca8e49044134fdbd8cab937ae173e558
--- /dev/null
+++ b/drivers/regulator/mt6311-regulator.c
@@ -0,0 +1,179 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Henry Chen <henryc.chen@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/regulator/mt6311.h>
+#include <linux/slab.h>
+#include "mt6311-regulator.h"
+
+static const struct regmap_config mt6311_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = MT6311_FQMTR_CON4,
+};
+
+/* Default limits measured in millivolts and milliamps */
+#define MT6311_MIN_UV 600000
+#define MT6311_MAX_UV 1393750
+#define MT6311_STEP_UV 6250
+
+static const struct regulator_linear_range buck_volt_range[] = {
+ REGULATOR_LINEAR_RANGE(MT6311_MIN_UV, 0, 0x7f, MT6311_STEP_UV),
+};
+
+static const struct regulator_ops mt6311_buck_ops = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+};
+
+static const struct regulator_ops mt6311_ldo_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+};
+
+#define MT6311_BUCK(_id) \
+{\
+ .name = #_id,\
+ .ops = &mt6311_buck_ops,\
+ .of_match = of_match_ptr(#_id),\
+ .regulators_node = of_match_ptr("regulators"),\
+ .type = REGULATOR_VOLTAGE,\
+ .id = MT6311_ID_##_id,\
+ .n_voltages = (MT6311_MAX_UV - MT6311_MIN_UV) / MT6311_STEP_UV + 1,\
+ .min_uV = MT6311_MIN_UV,\
+ .uV_step = MT6311_STEP_UV,\
+ .owner = THIS_MODULE,\
+ .linear_ranges = buck_volt_range, \
+ .n_linear_ranges = ARRAY_SIZE(buck_volt_range), \
+ .enable_reg = MT6311_VDVFS11_CON9,\
+ .enable_mask = MT6311_PMIC_VDVFS11_EN_MASK,\
+ .vsel_reg = MT6311_VDVFS11_CON12,\
+ .vsel_mask = MT6311_PMIC_VDVFS11_VOSEL_MASK,\
+}
+
+#define MT6311_LDO(_id) \
+{\
+ .name = #_id,\
+ .ops = &mt6311_ldo_ops,\
+ .of_match = of_match_ptr(#_id),\
+ .regulators_node = of_match_ptr("regulators"),\
+ .type = REGULATOR_VOLTAGE,\
+ .id = MT6311_ID_##_id,\
+ .owner = THIS_MODULE,\
+ .enable_reg = MT6311_LDO_CON3,\
+ .enable_mask = MT6311_PMIC_RG_VBIASN_EN_MASK,\
+}
+
+static const struct regulator_desc mt6311_regulators[] = {
+ MT6311_BUCK(VDVFS),
+ MT6311_LDO(VBIASN),
+};
+
+/*
+ * I2C driver interface functions
+ */
+static int mt6311_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ struct regmap *regmap;
+ int i, ret;
+ unsigned int data;
+
+ regmap = devm_regmap_init_i2c(i2c, &mt6311_regmap_config);
+ if (IS_ERR(regmap)) {
+ ret = PTR_ERR(regmap);
+ dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
+ ret);
+ return ret;
+ }
+
+ ret = regmap_read(regmap, MT6311_SWCID, &data);
+ if (ret < 0) {
+ dev_err(&i2c->dev, "Failed to read DEVICE_ID reg: %d\n", ret);
+ return ret;
+ }
+
+ switch (data) {
+ case MT6311_E1_CID_CODE:
+ case MT6311_E2_CID_CODE:
+ case MT6311_E3_CID_CODE:
+ break;
+ default:
+ dev_err(&i2c->dev, "Unsupported device id = 0x%x.\n", data);
+ return -ENODEV;
+ }
+
+ for (i = 0; i < MT6311_MAX_REGULATORS; i++) {
+ config.dev = &i2c->dev;
+ config.regmap = regmap;
+
+ rdev = devm_regulator_register(&i2c->dev,
+ &mt6311_regulators[i], &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&i2c->dev,
+ "Failed to register MT6311 regulator\n");
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static const struct i2c_device_id mt6311_i2c_id[] = {
+ {"mt6311", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, mt6311_i2c_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id mt6311_dt_ids[] = {
+ { .compatible = "mediatek,mt6311-regulator",
+ .data = &mt6311_i2c_id[0] },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mt6311_dt_ids);
+#endif
+
+static struct i2c_driver mt6311_regulator_driver = {
+ .driver = {
+ .name = "mt6311",
+ .of_match_table = of_match_ptr(mt6311_dt_ids),
+ },
+ .probe = mt6311_i2c_probe,
+ .id_table = mt6311_i2c_id,
+};
+
+module_i2c_driver(mt6311_regulator_driver);
+
+MODULE_AUTHOR("Henry Chen <henryc.chen@mediatek.com>");
+MODULE_DESCRIPTION("Regulator device driver for Mediatek MT6311");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/regulator/mt6311-regulator.h b/drivers/regulator/mt6311-regulator.h
new file mode 100644
index 0000000000000000000000000000000000000000..5218db46a798f4beb8d361c2e3d817cbad48c2bc
--- /dev/null
+++ b/drivers/regulator/mt6311-regulator.h
@@ -0,0 +1,65 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Henry Chen <henryc.chen@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MT6311_REGULATOR_H__
+#define __MT6311_REGULATOR_H__
+
+#define MT6311_SWCID 0x01
+
+#define MT6311_TOP_INT_CON 0x18
+#define MT6311_TOP_INT_MON 0x19
+
+#define MT6311_VDVFS11_CON0 0x87
+#define MT6311_VDVFS11_CON7 0x88
+#define MT6311_VDVFS11_CON8 0x89
+#define MT6311_VDVFS11_CON9 0x8A
+#define MT6311_VDVFS11_CON10 0x8B
+#define MT6311_VDVFS11_CON11 0x8C
+#define MT6311_VDVFS11_CON12 0x8D
+#define MT6311_VDVFS11_CON13 0x8E
+#define MT6311_VDVFS11_CON14 0x8F
+#define MT6311_VDVFS11_CON15 0x90
+#define MT6311_VDVFS11_CON16 0x91
+#define MT6311_VDVFS11_CON17 0x92
+#define MT6311_VDVFS11_CON18 0x93
+#define MT6311_VDVFS11_CON19 0x94
+
+#define MT6311_LDO_CON0 0xCC
+#define MT6311_LDO_OCFB0 0xCD
+#define MT6311_LDO_CON2 0xCE
+#define MT6311_LDO_CON3 0xCF
+#define MT6311_LDO_CON4 0xD0
+#define MT6311_FQMTR_CON0 0xD1
+#define MT6311_FQMTR_CON1 0xD2
+#define MT6311_FQMTR_CON2 0xD3
+#define MT6311_FQMTR_CON3 0xD4
+#define MT6311_FQMTR_CON4 0xD5
+
+#define MT6311_PMIC_RG_INT_POL_MASK 0x1
+#define MT6311_PMIC_RG_INT_EN_MASK 0x2
+#define MT6311_PMIC_RG_BUCK_OC_INT_STATUS_MASK 0x10
+
+#define MT6311_PMIC_VDVFS11_EN_CTRL_MASK 0x1
+#define MT6311_PMIC_VDVFS11_VOSEL_CTRL_MASK 0x2
+#define MT6311_PMIC_VDVFS11_EN_SEL_MASK 0x3
+#define MT6311_PMIC_VDVFS11_VOSEL_SEL_MASK 0xc
+#define MT6311_PMIC_VDVFS11_EN_MASK 0x1
+#define MT6311_PMIC_VDVFS11_VOSEL_MASK 0x7F
+#define MT6311_PMIC_VDVFS11_VOSEL_ON_MASK 0x7F
+#define MT6311_PMIC_VDVFS11_VOSEL_SLEEP_MASK 0x7F
+#define MT6311_PMIC_NI_VDVFS11_VOSEL_MASK 0x7F
+
+#define MT6311_PMIC_RG_VBIASN_EN_MASK 0x1
+
+#endif
diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c
index b1c485b24ab246234edbab2dfb4217e4fe1df833..250700c853bfa524991f6721256fb02876f54799 100644
--- a/drivers/regulator/of_regulator.c
+++ b/drivers/regulator/of_regulator.c
@@ -107,6 +107,9 @@ static void of_get_regulation_constraints(struct device_node *np,
if (!of_property_read_u32(np, "regulator-system-load", &pval))
constraints->system_load = pval;
+ constraints->over_current_protection = of_property_read_bool(np,
+ "regulator-over-current-protection");
+
for (i = 0; i < ARRAY_SIZE(regulator_states); i++) {
switch (i) {
case PM_SUSPEND_MEM:
diff --git a/drivers/regulator/pfuze100-regulator.c b/drivers/regulator/pfuze100-regulator.c
index 8cc8d1877c446a48737b5d337f9faf91dc6c37e1..2a44e5dd9c2a159b0efc5022fd205c34a9408e80 100644
--- a/drivers/regulator/pfuze100-regulator.c
+++ b/drivers/regulator/pfuze100-regulator.c
@@ -643,7 +643,6 @@ static struct i2c_driver pfuze_driver = {
.id_table = pfuze_device_id,
.driver = {
.name = "pfuze100-regulator",
- .owner = THIS_MODULE,
.of_match_table = pfuze_dt_ids,
},
.probe = pfuze100_regulator_probe,
@@ -653,4 +652,3 @@ module_i2c_driver(pfuze_driver);
MODULE_AUTHOR("Robin Gong <b38343@freescale.com>");
MODULE_DESCRIPTION("Regulator Driver for Freescale PFUZE100/PFUZE200 PMIC");
MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("i2c:pfuze100-regulator");
diff --git a/drivers/regulator/pwm-regulator.c b/drivers/regulator/pwm-regulator.c
index ffa96124a5e7206f4f86f7025098a3744f9ec315..fc3166dfcbfaa455b5105ef8e7715d3e17c56d6b 100644
--- a/drivers/regulator/pwm-regulator.c
+++ b/drivers/regulator/pwm-regulator.c
@@ -10,6 +10,7 @@
* published by the Free Software Foundation.
*/
+#include <linux/delay.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/err.h>
@@ -21,9 +22,15 @@
#include <linux/pwm.h>
struct pwm_regulator_data {
- struct pwm_voltages *duty_cycle_table;
+ /* Shared */
struct pwm_device *pwm;
+
+ /* Voltage table */
+ struct pwm_voltages *duty_cycle_table;
int state;
+
+ /* Continuous voltage */
+ int volt_uV;
};
struct pwm_voltages {
@@ -31,6 +38,9 @@ struct pwm_voltages {
unsigned int dutycycle;
};
+/**
+ * Voltage table call-backs
+ */
static int pwm_regulator_get_voltage_sel(struct regulator_dev *rdev)
{
struct pwm_regulator_data *drvdata = rdev_get_drvdata(rdev);
@@ -79,29 +89,129 @@ static int pwm_regulator_list_voltage(struct regulator_dev *rdev,
return drvdata->duty_cycle_table[selector].uV;
}
-static struct regulator_ops pwm_regulator_voltage_ops = {
+/**
+ * Continuous voltage call-backs
+ */
+static int pwm_voltage_to_duty_cycle_percentage(struct regulator_dev *rdev, int req_uV)
+{
+ int min_uV = rdev->constraints->min_uV;
+ int max_uV = rdev->constraints->max_uV;
+ int diff = max_uV - min_uV;
+
+ return 100 - (((req_uV * 100) - (min_uV * 100)) / diff);
+}
+
+static int pwm_regulator_get_voltage(struct regulator_dev *rdev)
+{
+ struct pwm_regulator_data *drvdata = rdev_get_drvdata(rdev);
+
+ return drvdata->volt_uV;
+}
+
+static int pwm_regulator_set_voltage(struct regulator_dev *rdev,
+ int min_uV, int max_uV,
+ unsigned *selector)
+{
+ struct pwm_regulator_data *drvdata = rdev_get_drvdata(rdev);
+ unsigned int ramp_delay = rdev->constraints->ramp_delay;
+ unsigned int period = pwm_get_period(drvdata->pwm);
+ int duty_cycle;
+ int ret;
+
+ duty_cycle = pwm_voltage_to_duty_cycle_percentage(rdev, min_uV);
+
+ ret = pwm_config(drvdata->pwm, (period / 100) * duty_cycle, period);
+ if (ret) {
+ dev_err(&rdev->dev, "Failed to configure PWM\n");
+ return ret;
+ }
+
+ ret = pwm_enable(drvdata->pwm);
+ if (ret) {
+ dev_err(&rdev->dev, "Failed to enable PWM\n");
+ return ret;
+ }
+ drvdata->volt_uV = min_uV;
+
+ /* Delay required by PWM regulator to settle to the new voltage */
+ usleep_range(ramp_delay, ramp_delay + 1000);
+
+ return 0;
+}
+
+static struct regulator_ops pwm_regulator_voltage_table_ops = {
.set_voltage_sel = pwm_regulator_set_voltage_sel,
.get_voltage_sel = pwm_regulator_get_voltage_sel,
.list_voltage = pwm_regulator_list_voltage,
.map_voltage = regulator_map_voltage_iterate,
};
+static struct regulator_ops pwm_regulator_voltage_continuous_ops = {
+ .get_voltage = pwm_regulator_get_voltage,
+ .set_voltage = pwm_regulator_set_voltage,
+};
+
static struct regulator_desc pwm_regulator_desc = {
.name = "pwm-regulator",
- .ops = &pwm_regulator_voltage_ops,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
.supply_name = "pwm",
};
+static int pwm_regulator_init_table(struct platform_device *pdev,
+ struct pwm_regulator_data *drvdata)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct pwm_voltages *duty_cycle_table;
+ unsigned int length = 0;
+ int ret;
+
+ of_find_property(np, "voltage-table", &length);
+
+ if ((length < sizeof(*duty_cycle_table)) ||
+ (length % sizeof(*duty_cycle_table))) {
+ dev_err(&pdev->dev,
+ "voltage-table length(%d) is invalid\n",
+ length);
+ return -EINVAL;
+ }
+
+ duty_cycle_table = devm_kzalloc(&pdev->dev, length, GFP_KERNEL);
+ if (!duty_cycle_table)
+ return -ENOMEM;
+
+ ret = of_property_read_u32_array(np, "voltage-table",
+ (u32 *)duty_cycle_table,
+ length / sizeof(u32));
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to read voltage-table\n");
+ return ret;
+ }
+
+ drvdata->duty_cycle_table = duty_cycle_table;
+ pwm_regulator_desc.ops = &pwm_regulator_voltage_table_ops;
+ pwm_regulator_desc.n_voltages = length / sizeof(*duty_cycle_table);
+
+ return 0;
+}
+
+static int pwm_regulator_init_continuous(struct platform_device *pdev,
+ struct pwm_regulator_data *drvdata)
+{
+ pwm_regulator_desc.ops = &pwm_regulator_voltage_continuous_ops;
+ pwm_regulator_desc.continuous_voltage_range = true;
+
+ return 0;
+}
+
static int pwm_regulator_probe(struct platform_device *pdev)
{
+ const struct regulator_init_data *init_data;
struct pwm_regulator_data *drvdata;
- struct property *prop;
struct regulator_dev *regulator;
struct regulator_config config = { };
struct device_node *np = pdev->dev.of_node;
- int length, ret;
+ int ret;
if (!np) {
dev_err(&pdev->dev, "Device Tree node missing\n");
@@ -112,44 +222,22 @@ static int pwm_regulator_probe(struct platform_device *pdev)
if (!drvdata)
return -ENOMEM;
- /* determine the number of voltage-table */
- prop = of_find_property(np, "voltage-table", &length);
- if (!prop) {
- dev_err(&pdev->dev, "No voltage-table\n");
- return -EINVAL;
- }
-
- if ((length < sizeof(*drvdata->duty_cycle_table)) ||
- (length % sizeof(*drvdata->duty_cycle_table))) {
- dev_err(&pdev->dev, "voltage-table length(%d) is invalid\n",
- length);
- return -EINVAL;
- }
-
- pwm_regulator_desc.n_voltages = length / sizeof(*drvdata->duty_cycle_table);
-
- drvdata->duty_cycle_table = devm_kzalloc(&pdev->dev,
- length, GFP_KERNEL);
- if (!drvdata->duty_cycle_table)
- return -ENOMEM;
-
- /* read voltage table from DT property */
- ret = of_property_read_u32_array(np, "voltage-table",
- (u32 *)drvdata->duty_cycle_table,
- length / sizeof(u32));
- if (ret < 0) {
- dev_err(&pdev->dev, "read voltage-table failed\n");
+ if (of_find_property(np, "voltage-table", NULL))
+ ret = pwm_regulator_init_table(pdev, drvdata);
+ else
+ ret = pwm_regulator_init_continuous(pdev, drvdata);
+ if (ret)
return ret;
- }
- config.init_data = of_get_regulator_init_data(&pdev->dev, np,
- &pwm_regulator_desc);
- if (!config.init_data)
+ init_data = of_get_regulator_init_data(&pdev->dev, np,
+ &pwm_regulator_desc);
+ if (!init_data)
return -ENOMEM;
config.of_node = np;
config.dev = &pdev->dev;
config.driver_data = drvdata;
+ config.init_data = init_data;
drvdata->pwm = devm_pwm_get(&pdev->dev, NULL);
if (IS_ERR(drvdata->pwm)) {
diff --git a/drivers/regulator/tps51632-regulator.c b/drivers/regulator/tps51632-regulator.c
index c213e37eb69e06c65a2d592c00afff2e0a92f4ef..572816e30095aebac1025e5a97343c4272cde2d5 100644
--- a/drivers/regulator/tps51632-regulator.c
+++ b/drivers/regulator/tps51632-regulator.c
@@ -362,7 +362,6 @@ MODULE_DEVICE_TABLE(i2c, tps51632_id);
static struct i2c_driver tps51632_i2c_driver = {
.driver = {
.name = "tps51632",
- .owner = THIS_MODULE,
.of_match_table = of_match_ptr(tps51632_of_match),
},
.probe = tps51632_probe,
diff --git a/drivers/regulator/tps62360-regulator.c b/drivers/regulator/tps62360-regulator.c
index a1fd626c6c966fb13dce292120278a33e378a3a2..f6a6d36a65334b60257b320870483e219e71746a 100644
--- a/drivers/regulator/tps62360-regulator.c
+++ b/drivers/regulator/tps62360-regulator.c
@@ -515,7 +515,6 @@ MODULE_DEVICE_TABLE(i2c, tps62360_id);
static struct i2c_driver tps62360_i2c_driver = {
.driver = {
.name = "tps62360",
- .owner = THIS_MODULE,
.of_match_table = of_match_ptr(tps62360_of_match),
},
.probe = tps62360_probe,
diff --git a/drivers/regulator/tps65023-regulator.c b/drivers/regulator/tps65023-regulator.c
index b941e564b3f3405a647b0d13794eed5d3dffa3fc..5cc19b44974aa69065c9eff9f8607eb41a7d928e 100644
--- a/drivers/regulator/tps65023-regulator.c
+++ b/drivers/regulator/tps65023-regulator.c
@@ -410,7 +410,6 @@ MODULE_DEVICE_TABLE(i2c, tps_65023_id);
static struct i2c_driver tps_65023_i2c_driver = {
.driver = {
.name = "tps65023",
- .owner = THIS_MODULE,
},
.probe = tps_65023_probe,
.id_table = tps_65023_id,
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index 4db9fbe4889d3c54f76c2c2c1e3d50ce404d0965..45932228cbf5924c507bbc4b39c405bb9ab750f7 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -148,6 +148,7 @@ struct regulator_ops {
int (*get_current_limit) (struct regulator_dev *);
int (*set_input_current_limit) (struct regulator_dev *, int lim_uA);
+ int (*set_over_current_protection) (struct regulator_dev *);
/* enable/disable regulator */
int (*enable) (struct regulator_dev *);
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index b11be126012974ebf4877220c8949310d649ddea..a1067d0b39916b869eebc6a179c3696a115e3996 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -147,6 +147,7 @@ struct regulation_constraints {
unsigned ramp_disable:1; /* disable ramp delay */
unsigned soft_start:1; /* ramp voltage slowly */
unsigned pull_down:1; /* pull down resistor when regulator off */
+ unsigned over_current_protection:1; /* auto disable on over current */
};
/**
diff --git a/include/linux/regulator/mt6311.h b/include/linux/regulator/mt6311.h
new file mode 100644
index 0000000000000000000000000000000000000000..8473259395b692e631ade622bd86138c5e8a1bc2
--- /dev/null
+++ b/include/linux/regulator/mt6311.h
@@ -0,0 +1,29 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Henry Chen <henryc.chen@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __LINUX_REGULATOR_MT6311_H
+#define __LINUX_REGULATOR_MT6311_H
+
+#define MT6311_MAX_REGULATORS 2
+
+enum {
+ MT6311_ID_VDVFS = 0,
+ MT6311_ID_VBIASN,
+};
+
+#define MT6311_E1_CID_CODE 0x10
+#define MT6311_E2_CID_CODE 0x20
+#define MT6311_E3_CID_CODE 0x30
+
+#endif /* __LINUX_REGULATOR_MT6311_H */